Lincoln Electric IM10044 manual Battery Jump Start Terminal

Page 23

B-5	OPERATION	B-5

23. 415 VAC RECEPTACLE

This is a 415VAC receptacle that provides auxil- iary power. This receptacle has 32 amp rating and IP66 rated . Refer to the AUXILIARY POWER RECEPTACLES section in the installa- tion chapter for further information about these receptacles . Also refer to the AUXILIARY POWER OPERATION section later in this chap- ter.

24. GROUND STUD:

Provides a connection point for connecting the machine case to earth ground . Refer to “MACHINE GROUNDING” in the Installation chapter for proper machine grounding informa- tion.

25. RCD:

“Residual Current Device” provides protection from active to ground contact.

RCD will not protect against electrical shock resulting from contact with active and neutral wires.

26. VRD INDICATOR LIGHTS:

Indicates OCV voltage across the output termi- nals. Also indicates operation of VRD in CC mode. A Green light indicates OCV below 30V and a red light indicates OCV above 30V.

During welding both lights will flash, depending on the type of Consumable being used.

BATTERY JUMP START TERMINAL (27-28)

27.POSITIVE BATTERY JUMP START TERMINAL.

28.NEGATIVE BATTERY JUMP START TERMINAL.

12V battery jump start feature is standard . Covered output studs for convenient access, and protection against accidental impact. can be used to jump-start a utility truck with up to 800 cold cranking amps. Can also be used to jump-start the VANTAGE® 575 CUMMINS.

29. BATTERY DISCONNECT SWITCH

Battery disconnect switch provides lockout/tagout capability. Switch is conveniently located on the front bottom of the machine.

30. AIR CLEANER SERVICE INDICATOR

Air cleaner service indicator provides a Go/No-Go visual indication of useful filter service life. Also located inside the engine compartment. (SEE FIG- URE B.2)

FIGURE B.2

30

VANTAGE® 575 CUMMINS

Image 23

Contents Vantage Cummins California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéElectromagnetic Compatibility EMC Safety Thank You Table of Contents Table of Contents Installation Stacking Safety PrecautionsLocation and Ventilation StoringTowing High Temperature OperationLifting High Altitude OperationFuel USE Diesel Fuel only PRE-OPERATION Engine and COM- Pressor ServiceBattery Connection OILWelding Terminals AIR Cleaner Inlet HoodMuffler Outlet Pipe Spark ArrestorStandby Power Connections Remote ControlAuxiliary Power Receptacles Control Cable Model Connection of Lincoln ELEC- Tric Wire FeedersConnection of LN-15 to the Vantage 575 CUM Across The-Arc ModelShut off welder before making any electrical con- nections Connection of the LN-25 to the VAN- Tage 575 CumminsRecommended Applications Safety PrecautionsOperation General DescriptionControls and Settings Engine Protection Battery Charging LightIdler Switch OIL Pressure GaugePIN Connector Weld Mode Selector SwitchWelding Terminals Switch Wire Feeder Voltmeter SwitchBattery Jump Start Terminal What are VRD and Rocv DEVICES? Welding Power SourcesSafety VRD Operation IndicatorTable B.1 Cummins B3.3 Engine Fuel Consumption Starting TechniqueBREAK-IN Period Typical Fuel ConsumptionWelder Operation Stick Welding ModeCC-STICK Mode Touch Start TIG ModeTable B.3 Typical Current Ranges Wire WELDING-CVARC Gouging Carbon Diameter Current Range DC, elec Trode positiveParalleling Auxiliary Power OperationSimultaneous Welding and Auxiliary Power Loads TIG Options AccessoriesOptional Field Installed Accessories Weekly MaintenanceRoutine and Periodic Maintenance Daily Engine MaintenanceService Instructions Fuel Filters Battery HandlingPreventing Battery Discharge Preventing Battery BucklingWelder / Generator MAINTE- Nance HOW to USE Troubleshooting Guide TroubleshootingContact your local Lincoln Authorized Field Service FacilityTroubleshooting PCB Wiring Diagram Diagrams To Work Electrode Cable To Wire Feed Unit Engine Welders / K867 / K775 / LN-7 Connection DiagramDiagrams Diagrams Engine Welders / K867 / LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams 736 634 24 .97 Dimension PrintPrecaucion Warnung