Lincoln Electric IM10044 manual Engine Welders / K867 / LN-8 Connection Diagram

Page 43

ENGINE WELDERS / K867 / LN-8 CONNECTION DIAGRAM

WARNING

Do not operate with panels open.	Keep guards in place.
Disconnect NEGATIVE (-) BATTERY LEAD	Keep away from moving parts.
before servicing.	Only qualified personnel should install,use
Do not touch electrically live parts.	or service this equipment.
SPARE	}
41	}
82		LN-8
81	N.C.	WIRE
42		FEEDER
42

F-6

VANTAGE® 575 CUMMINS

		31
		32
		14 PIN
		AMPHENOL
		2
		4
ELECTRODE	TO WORK	21
		K867 UNIVERSAL
		GND
		ADAPTER PLUG

	TO WORK	75
	ELECTRODE CABLE	76
	ELECTRODE CABLE	77
	TO WIRE FEED UNIT	77

CAUTION :

} N.D.

31

32

2

4

21

GND

A

B

C

K196

INPUT CABLE

DIAGRAMS

ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE

AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE

DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN

THE ENGINE WELDER OPERATING MANUAL.

N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE

APPICATIONS. SEE OPERATING MANUAL.

N.B. USE VOLTMETER SWITCH TO SELECT DESIRED ELECTRODE POLARITY. POSITION THE SELECTOR SWITCH TO "WIRE WELDING CV".

N.C. INSULATE EACH UNUSED LEAD INDIVIDUALLY.

N.D. SPLICE LEADS AND INSULATE.

7-2000

S23989

F-6

Image 43

Contents Vantage Cummins California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéElectromagnetic Compatibility EMC Safety Thank You Table of Contents Table of Contents Installation Stacking Safety PrecautionsLocation and Ventilation StoringTowing High Temperature OperationLifting High Altitude OperationFuel USE Diesel Fuel only PRE-OPERATION Engine and COM- Pressor ServiceBattery Connection OILWelding Terminals AIR Cleaner Inlet HoodMuffler Outlet Pipe Spark ArrestorAuxiliary Power Receptacles Remote ControlStandby Power Connections Control Cable Model Connection of Lincoln ELEC- Tric Wire FeedersConnection of LN-15 to the Vantage 575 CUM Across The-Arc ModelShut off welder before making any electrical con- nections Connection of the LN-25 to the VAN- Tage 575 CumminsRecommended Applications Safety PrecautionsOperation General DescriptionControls and Settings Engine Protection Battery Charging LightIdler Switch OIL Pressure GaugePIN Connector Weld Mode Selector SwitchWelding Terminals Switch Wire Feeder Voltmeter SwitchBattery Jump Start Terminal What are VRD and Rocv DEVICES? Welding Power SourcesSafety VRD Operation IndicatorTable B.1 Cummins B3.3 Engine Fuel Consumption Starting TechniqueBREAK-IN Period Typical Fuel ConsumptionWelder Operation Stick Welding ModeCC-STICK Mode Touch Start TIG ModeTable B.3 Typical Current Ranges Wire WELDING-CVARC Gouging Carbon Diameter Current Range DC, elec Trode positiveSimultaneous Welding and Auxiliary Power Loads Auxiliary Power OperationParalleling Optional Field Installed Accessories AccessoriesTIG Options Weekly MaintenanceRoutine and Periodic Maintenance Daily Engine MaintenanceService Instructions Fuel Filters Battery HandlingPreventing Battery Discharge Preventing Battery BucklingWelder / Generator MAINTE- Nance HOW to USE Troubleshooting Guide TroubleshootingContact your local Lincoln Authorized Field Service FacilityTroubleshooting PCB Wiring Diagram Diagrams To Work Electrode Cable To Wire Feed Unit Engine Welders / K867 / K775 / LN-7 Connection DiagramDiagrams Diagrams Engine Welders / K867 / LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams 736 634 24 .97 Dimension PrintPrecaucion Warnung