Lincoln Electric IM10044 manual Welder / Generator MAINTE- Nance

Page 33

D-4

MAINTENANCE

D-4

 

 

 

CHARGING THE BATTERY

When you charge, jump, replace, or otherwise connect battery cables to the battery, be sure the polarity is correct. Improper polarity can damage the charging circuit. The VANTAGE® 575 CUMMINS positive (+) battery terminal has a red terminal cover.

If you need to charge the battery with an external charger, disconnect the negative cable first, then the positive cable before you attach the charger leads. after the battery is charged, reconnect the positive bat- tery cable first and the negative cable last. Failure to do so can result in damage to the internal charger components.

Follow the instructions of the battery charger manufac- turer for proper charger settings and charging time.

WELDER / GENERATOR MAINTE- NANCE

STORAGE

Store the VANTAGE® 575 CUMMINS in a clean, dry protected areas.

CLEANING

Blow out the generator and controls periodically with low pressure air. Do this at least once a week in par- ticularly dirty areas.

BRUSH REMOVAL AND REPLACEMENT

It is normal for the brushes and slip rings to wear and darken slightly. Inspect the brushes when a generator overhaul is necessary.

NAMEPLATES / WARNING DECALS MAIN- TENANCE

Whenever routine maintenance is performed on this machine - or at least yearly - inspect all nameplates and labels for legibility. Replace those which are no longer clear. Refer to the parts list for the replacement item number.

WARNING

Do not attempt to polish slip rings while the engine is running.

------------------------------------------------------------------------

Table D.1 Engine Maintenance Components

 

ITEM

MAKE

PART NUMBER

SERVICE INTERVAL

 

 

Air Cleaner Element

Donaldson

P822768

Replace as indicated by

 

 

 

 

Service Indicator

 

 

Fleetguard

AF25436

 

 

 

Oil Filer

Cummins

C6002112110

Replace every 750 hours or 3 months,

 

 

Fleetguard

LF16011

whichever is less.

 

 

Fan Belt

Cummins

C0412021749

Inspect every 1000 hours or 12 months,

 

 

 

 

whichever is less.

 

 

Fuel Strainer

Cummins

3826094

Inspect and replace monthly as

 

 

Fleetguard

FF5079

required. Replace annually.

 

 

Fuel Filter /

Fleetguard

FS19594

Replace every 500 hours or 6 months,

 

Water Separator

 

 

whichever is less.

 

 

Battery

-----

BCI GROUP 34

Inspect every 500 hours

 

 

Engine Oil Change

See Manual

-----

Change every 750 hours or 3 months,

 

 

 

 

whichever is less. Check daily.

 

 

 

 

 

 

VANTAGE® 575 CUMMINS

Image 33
Contents Vantage Cummins California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéElectromagnetic Compatibility EMC Safety Thank You Table of Contents Table of Contents Installation Location and Ventilation Safety PrecautionsStoring StackingLifting High Temperature OperationHigh Altitude Operation TowingBattery Connection PRE-OPERATION Engine and COM- Pressor ServiceOIL Fuel USE Diesel Fuel onlyMuffler Outlet Pipe AIR Cleaner Inlet HoodSpark Arrestor Welding TerminalsRemote Control Auxiliary Power ReceptaclesStandby Power Connections Connection of LN-15 to the Vantage 575 CUM Connection of Lincoln ELEC- Tric Wire FeedersAcross The-Arc Model Control Cable ModelShut off welder before making any electrical con- nections Connection of the LN-25 to the VAN- Tage 575 CumminsOperation Safety PrecautionsGeneral Description Recommended ApplicationsControls and Settings Idler Switch Battery Charging LightOIL Pressure Gauge Engine ProtectionWelding Terminals Switch Weld Mode Selector SwitchWire Feeder Voltmeter Switch PIN ConnectorBattery Jump Start Terminal Safety Welding Power SourcesVRD Operation Indicator What are VRD and Rocv DEVICES?BREAK-IN Period Starting TechniqueTypical Fuel Consumption Table B.1 Cummins B3.3 Engine Fuel ConsumptionCC-STICK Mode Stick Welding ModeTouch Start TIG Mode Welder OperationARC Gouging Wire WELDING-CVCarbon Diameter Current Range DC, elec Trode positive Table B.3 Typical Current RangesAuxiliary Power Operation Simultaneous Welding and Auxiliary Power LoadsParalleling Accessories Optional Field Installed AccessoriesTIG Options Routine and Periodic Maintenance Daily MaintenanceEngine Maintenance WeeklyService Instructions Preventing Battery Discharge Battery HandlingPreventing Battery Buckling Fuel FiltersWelder / Generator MAINTE- Nance HOW to USE Troubleshooting Guide TroubleshootingContact your local Lincoln Authorized Field Service FacilityTroubleshooting PCB Wiring Diagram Diagrams To Work Electrode Cable To Wire Feed Unit Engine Welders / K867 / K775 / LN-7 Connection DiagramDiagrams Diagrams Engine Welders / K867 / LN-8 Connection Diagram Diagrams Diagrams Diagrams Diagrams Diagrams Diagrams 736 634 24 .97 Dimension PrintPrecaucion Warnung