Lincoln Electric IM644-A manual Commander / K867 / LN-8 Connection Diagram

Page 42

COMMANDER / K867 / LN-8 CONNECTION DIAGRAM

WARNING

Do not operate with panels open.

Keep guards in place.

Disconnect NEGATIVE (-) BATTERY LEAD

Keep away from moving parts.

before servicing.

Only qualified personnel should install,use

Do not touch electrically live parts.

or service this equipment.

CONNECTION DIAGRAM:

F-6

COMMANDER 500

ELECTRODE

TO WORK

14PIN AMPHENOL

K867 UNIVERSAL

ADAPTER PLUG

SPARE 82 81 42 41

31

32

2

4

21 GND

}N.C.

31

32

2

4

21

GND

LN-8

WIRE

FEEDER

K196

INPUT CABLE

DIAGRAMS

TO WORK

ELECTRODE CABLE

TO WIRE FEED UNIT

CAUTION :

75

76

77

 

A

 

B

}

C

 

N.D.

 

ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN

THE ENGINE WELDER OPERATING MANUAL.

N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPICATIONS. SEE OPERATING MANUAL.

N.B. USE VOLTMETER SWITCH TO SELECT DESIRED ELECTRODE POLARITY. POSITION THE SELECTOR SWITCH TO "WIRE WELDING CV". PLACE LOCAL / REMOTE SWITCH IN "REMOTE" POSITION.

N.C. INSULATE EACH UNUSED LEAD INDIVIDUALLY. N.D. SPLICE LEADS AND INSULATE.

7-18-98

S23989

F-6

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Commander Safety Depends on YouSafety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Section E Section CSection D Section FHEIGHT2 Width Depth Weight InstallationWelding Range Open Circuit Voltage Auxiliary Power1 Bore x StrokeStoring Safety PrecautionsLocation / Ventilation StackingHigh Altitude Operation High Temperature OperationLifting TowingOIL PRE-OPERATION Engine ServiceEngine Cooling System Battery Connection Fuel USE Diesel Fuel onlyRemote Control High Frequency Generators for TIG ApplicationsWelding Terminals Welding Output Cables Auxiliary Power ReceptaclesStandby Power Connections Machine GroundingPower Connection of Lincoln Electric Wire Feeders Connection of the LN-25 to the CommanderConnection of LN-7 or LN-8 to the Commander Connection of AN LN-23P Wire Feeder to the Commander Operation Safety InstructionsDesign Features and Advantages Operating InstructionsK1639-1 Commander 500 Standard Model For Auxiliary PowerOther Features Welding CapabilityStart Pushbutton Controls and SettingsRUN- Stop Switch Fuel Level Gauge and LightIdler Operational exceptions Idler SwitchOIL Pressure Gauge K1639-2 Std., K1639-1 Opt. and Light Hour MeterAuxiliary Power Controls Engine Operation Starting the EngineStopping the Engine Typical Fuel Consumption Welder OperationBREAK-IN Period Stick WeldingCommander 500 Settings When Using the K799 HI-FREQ Unit Commander 500 Settings When Using the K930-1 TIG ModuleTable B.3 Typical Current Ranges 1 for Tungsten ELECTRODES2 Auxiliary Power Operation Wire Feed Constant Voltage WELD- INGSimultaneous Welding and AUXIL- Iary Power Loads Table B.4 Commander 500 Simultaneous Welding and Power Loads Accessories Optional Field Installed AccessoriesRecommended Optional Equipment Maintenance Routine and Periodic MaintenanceEngine Maintenance Fuel Filters Fuel PRE-FILTER/WATER Separator ASSEM- BLYWater Separator Element Battery Handling Cooling System Cooling Blower BeltCleaning Nameplates / Warning Decals MaintenanceWelder / Generator Maintenance Brush Removal and ReplacementTroubleshooting HOW to USE Troubleshooting GuideSymptoms Possible AreasCourse of Action Function Problems Output Problems Diagrams Commander 500 Wiring DiagramConnection Diagram Commander / K867 / K775 / LN-7 Connection Diagram To Work Electrode Cable To Wire Feed UnitTo Wire Feed Unit Connection DiagramRemote Control Electrode CableConnection Diagram Commander to K867 Adapter Connection DiagramCommander / K867 / LN-8 Connection Diagram Remove the Three Screws Shown and USE PIN Amphenol Commander / LN-8 Connection Diagram To LN-8 Input Cable Plug K595 Control CableTo Work To Work PIN Commander / K930 TIG Module / Connection Diagram Commander / LN-742 Connection Diagram To LN-742 Input Cable Plug K592 Control CableDimension Print 24.97Basic Course $700.00Precaucion Aviso DE
Top Page Image Contents