Lincoln Electric IM644-A manual Commander / LN-8 Connection Diagram, To Work

Page 45

COMMANDER / LN-8 CONNECTION DIAGRAM

WARNING

Do not operate with panels open.

Keep guards in place.

Disconnect NEGATIVE (-) BATTERY LEAD

Keep away from moving parts.

before servicing.

Only qualified personnel should install,use

Do not touch electrically live parts.

or service this equipment.

CONNECTION DIAGRAM:

F-9

COMMANDER 500

ELECTRODE

TO WORK

TO LN-8 INPUT

CABLE PLUG

K595 CONTROL CABLE

14PIN AMPHENOL

DIAGRAMS

 

TO WORK

 

ELECTRODE CABLE

CAUTION :

TO WIRE FEED UNIT

ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN

THE ENGINE WELDER OPERATING MANUAL.

N.A. WELDING CABLES MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL.

N.B. USE VOLTMETER SWITCH TO SELECT DESIRED ELECTRODE POLARITY. POSITION THE SELECTOR SWITCH TO "WIRE WELDING CV". PLACE LOCAL / REMOTE SWITCH IN "REMOTE" POSITION.

7-18-98

S23992

F-9

Image 45
Contents Safety Depends on You CommanderCalifornia Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéThank You Table of Contents Section D Section CSection E Section FWelding Range Open Circuit Voltage Auxiliary Power1 InstallationHEIGHT2 Width Depth Weight Bore x StrokeLocation / Ventilation Safety PrecautionsStoring StackingLifting High Temperature OperationHigh Altitude Operation TowingEngine Cooling System Battery Connection PRE-OPERATION Engine ServiceOIL Fuel USE Diesel Fuel onlyRemote Control High Frequency Generators for TIG ApplicationsWelding Terminals Standby Power Connections Auxiliary Power ReceptaclesWelding Output Cables Machine GroundingPower Connection of Lincoln Electric Wire Feeders Connection of the LN-25 to the CommanderConnection of LN-7 or LN-8 to the Commander Connection of AN LN-23P Wire Feeder to the Commander Design Features and Advantages Safety InstructionsOperation Operating InstructionsOther Features For Auxiliary PowerK1639-1 Commander 500 Standard Model Welding CapabilityRUN- Stop Switch Controls and SettingsStart Pushbutton Fuel Level Gauge and LightOIL Pressure Gauge K1639-2 Std., K1639-1 Opt. and Light Idler SwitchIdler Operational exceptions Hour MeterAuxiliary Power Controls Engine Operation Starting the EngineStopping the Engine BREAK-IN Period Welder OperationTypical Fuel Consumption Stick WeldingCommander 500 Settings When Using the K799 HI-FREQ Unit Commander 500 Settings When Using the K930-1 TIG ModuleTable B.3 Typical Current Ranges 1 for Tungsten ELECTRODES2 Auxiliary Power Operation Wire Feed Constant Voltage WELD- INGSimultaneous Welding and AUXIL- Iary Power Loads Table B.4 Commander 500 Simultaneous Welding and Power Loads Accessories Optional Field Installed AccessoriesRecommended Optional Equipment Maintenance Routine and Periodic MaintenanceEngine Maintenance Fuel Filters Fuel PRE-FILTER/WATER Separator ASSEM- BLYWater Separator Element Cooling System Cooling Blower Belt Battery HandlingWelder / Generator Maintenance Nameplates / Warning Decals MaintenanceCleaning Brush Removal and ReplacementHOW to USE Troubleshooting Guide TroubleshootingSymptoms Possible AreasCourse of Action Function Problems Output Problems Commander 500 Wiring Diagram DiagramsConnection Diagram To Work Electrode Cable To Wire Feed Unit Commander / K867 / K775 / LN-7 Connection DiagramRemote Control Connection DiagramTo Wire Feed Unit Electrode CableCommander to K867 Adapter Connection Diagram Connection DiagramCommander / K867 / LN-8 Connection Diagram Remove the Three Screws Shown and USE PIN Amphenol Commander / LN-8 Connection Diagram To LN-8 Input Cable Plug K595 Control CableTo Work To Work PIN Commander / K930 TIG Module / Connection Diagram To LN-742 Input Cable Plug K592 Control Cable Commander / LN-742 Connection Diagram24.97 Dimension Print$700.00 Basic CoursePrecaucion Aviso DE