Lincoln Electric IM644-A manual PIN Amphenol

Page 44

COMMANDER / LN-25 ACROSS THE ARC CONNECTION DIAGRAM WITH OPTIONAL K857 REMOTE CONTROL

WARNING

Do not operate with panels open.	Keep guards in place.
Disconnect NEGATIVE (-) BATTERY LEAD	Keep away from moving parts.
before servicing.	Only qualified personnel should install,use
Do not touch electrically live parts.	or service this equipment.

CONNECTION DIAGRAM:

F-8

COMMANDER 500

6PIN AMPHENOL

14 PIN AMPHENOL

ELECTRODE

TO WORK

ELECTRODE

OPTIONAL K857 OR K857-1

REMOTE CONTROL

LN-25

WIRE FEEDER

WORK CLIP LEAD

TO WORK

DIAGRAMS

CABLE

TO WORK

N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL.

N.B. USE VOLTMETER SWITCH TO SELECT DESIRED ELECTRODE POLARITY.

N.C. IF REMOTE OUTPUT CONTROL IS USED, PLACE LOCAL REMOTE SWITCH IN "REMOTE" POSITION.

N.D. THE OUTPUT CONTROL SWITCH MUST BE IN THE "WELDING TERMINALS ALWAYS ON" POSITION .

7-21-98

S23991

F-8

Image 44

Contents Commander Safety Depends on YouSafety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Section C Section DSection E Section FInstallation Welding Range Open Circuit Voltage Auxiliary Power1HEIGHT2 Width Depth Weight Bore x StrokeSafety Precautions Location / VentilationStoring StackingHigh Temperature Operation LiftingHigh Altitude Operation TowingPRE-OPERATION Engine Service Engine Cooling System Battery ConnectionOIL Fuel USE Diesel Fuel onlyWelding Terminals Remote ControlHigh Frequency Generators for TIG Applications Auxiliary Power Receptacles Standby Power ConnectionsWelding Output Cables Machine GroundingPower Connection of LN-7 or LN-8 to the Commander Connection of Lincoln Electric Wire FeedersConnection of the LN-25 to the Commander Connection of AN LN-23P Wire Feeder to the Commander Safety Instructions Design Features and AdvantagesOperation Operating InstructionsFor Auxiliary Power Other FeaturesK1639-1 Commander 500 Standard Model Welding CapabilityControls and Settings RUN- Stop SwitchStart Pushbutton Fuel Level Gauge and LightIdler Switch OIL Pressure Gauge K1639-2 Std., K1639-1 Opt. and LightIdler Operational exceptions Hour MeterAuxiliary Power Controls Stopping the Engine Engine OperationStarting the Engine Welder Operation BREAK-IN PeriodTypical Fuel Consumption Stick WeldingTable B.3 Typical Current Ranges 1 for Tungsten ELECTRODES2 Commander 500 Settings When Using the K799 HI-FREQ UnitCommander 500 Settings When Using the K930-1 TIG Module Simultaneous Welding and AUXIL- Iary Power Loads Auxiliary Power OperationWire Feed Constant Voltage WELD- ING Table B.4 Commander 500 Simultaneous Welding and Power Loads Recommended Optional Equipment AccessoriesOptional Field Installed Accessories Engine Maintenance MaintenanceRoutine and Periodic Maintenance Water Separator Element Fuel FiltersFuel PRE-FILTER/WATER Separator ASSEM- BLY Battery Handling Cooling System Cooling Blower BeltNameplates / Warning Decals Maintenance Welder / Generator MaintenanceCleaning Brush Removal and ReplacementTroubleshooting HOW to USE Troubleshooting GuideCourse of Action SymptomsPossible Areas Function Problems Output Problems Diagrams Commander 500 Wiring DiagramConnection Diagram Commander / K867 / K775 / LN-7 Connection Diagram To Work Electrode Cable To Wire Feed UnitConnection Diagram Remote ControlTo Wire Feed Unit Electrode CableConnection Diagram Commander to K867 Adapter Connection DiagramCommander / K867 / LN-8 Connection Diagram Remove the Three Screws Shown and USE PIN Amphenol To Work Commander / LN-8 Connection DiagramTo LN-8 Input Cable Plug K595 Control Cable To Work PIN Commander / K930 TIG Module / Connection Diagram Commander / LN-742 Connection Diagram To LN-742 Input Cable Plug K592 Control CableDimension Print 24.97Basic Course $700.00Precaucion Aviso DE