Lincoln Electric IM644-A manual Pin

Page 47

COMMANDER 500

COMMANDER/ LN-25 ACROSS THE ARC CONNECTION DIAGRAM

WITH OPTIONAL K444-1 REMOTE CONTROL

	WARNING
	Do not operate with panels open.	Keep guards in place.
	Disconnect NEGATIVE (-) BATTERY LEAD	Keep away from moving parts.
	before servicing.	Only qualified personnel should install,use
	Do not touch electrically live parts.	or service this equipment.
6 PIN	14 PIN
6 PIN	AMPHENOL
AMPHENOL
		OPTIONAL K444-1
		REMOTE CONTROL
		LN-25
		WIRE FEEDER
ELECTRODE	TO WORK	WORK CLIP LEAD

TO WORK

ELECTRODE	TO WORK
CABLE

N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL.

N.B. USE VOLTMETER SWITCH TO SELECT DESIRED ELECTRODE POLARITY.

N.C. IF REMOTE OUTPUT CONTROL IS USED, PLACE LOCAL REMOTE SWITCH IN "REMOTE" POSITION.

N.D. THE OUTPUT CONTROL SWITCH MUST BE IN THE "WELDING TERMINALS ALWAYS ON" POSITION .

7-18-98

S23994

CONNECTION DIAGRAM:

F-11

DIAGRAMS

F-11

Image 47

Contents Safety Depends on You CommanderCalifornia Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéThank You Table of Contents Section F Section CSection D Section EBore x Stroke InstallationWelding Range Open Circuit Voltage Auxiliary Power1 HEIGHT2 Width Depth WeightStacking Safety PrecautionsLocation / Ventilation StoringTowing High Temperature OperationLifting High Altitude OperationFuel USE Diesel Fuel only PRE-OPERATION Engine ServiceEngine Cooling System Battery Connection OILWelding Terminals Remote ControlHigh Frequency Generators for TIG Applications Machine Grounding Auxiliary Power ReceptaclesStandby Power Connections Welding Output CablesPower Connection of LN-7 or LN-8 to the Commander Connection of Lincoln Electric Wire FeedersConnection of the LN-25 to the Commander Connection of AN LN-23P Wire Feeder to the Commander Operating Instructions Safety InstructionsDesign Features and Advantages OperationWelding Capability For Auxiliary PowerOther Features K1639-1 Commander 500 Standard ModelFuel Level Gauge and Light Controls and SettingsRUN- Stop Switch Start PushbuttonHour Meter Idler SwitchOIL Pressure Gauge K1639-2 Std., K1639-1 Opt. and Light Idler Operational exceptionsAuxiliary Power Controls Stopping the Engine Engine OperationStarting the Engine Stick Welding Welder OperationBREAK-IN Period Typical Fuel ConsumptionTable B.3 Typical Current Ranges 1 for Tungsten ELECTRODES2 Commander 500 Settings When Using the K799 HI-FREQ UnitCommander 500 Settings When Using the K930-1 TIG Module Simultaneous Welding and AUXIL- Iary Power Loads Auxiliary Power OperationWire Feed Constant Voltage WELD- ING Table B.4 Commander 500 Simultaneous Welding and Power Loads Recommended Optional Equipment AccessoriesOptional Field Installed Accessories Engine Maintenance MaintenanceRoutine and Periodic Maintenance Water Separator Element Fuel FiltersFuel PRE-FILTER/WATER Separator ASSEM- BLY Cooling System Cooling Blower Belt Battery HandlingBrush Removal and Replacement Nameplates / Warning Decals MaintenanceWelder / Generator Maintenance CleaningHOW to USE Troubleshooting Guide TroubleshootingCourse of Action SymptomsPossible Areas Function Problems Output Problems Commander 500 Wiring Diagram DiagramsConnection Diagram To Work Electrode Cable To Wire Feed Unit Commander / K867 / K775 / LN-7 Connection DiagramElectrode Cable Connection DiagramRemote Control To Wire Feed UnitCommander to K867 Adapter Connection Diagram Connection DiagramCommander / K867 / LN-8 Connection Diagram Remove the Three Screws Shown and USE PIN Amphenol To Work Commander / LN-8 Connection DiagramTo LN-8 Input Cable Plug K595 Control Cable To Work PIN Commander / K930 TIG Module / Connection Diagram To LN-742 Input Cable Plug K592 Control Cable Commander / LN-742 Connection Diagram24.97 Dimension Print$700.00 Basic CoursePrecaucion Aviso DE