Makita 5377MG-R instruction manual Makita Limited ONE Year Warranty, Warranty Policy

Page 11

MAKITA LIMITED ONE YEAR WARRANTY

Warranty Policy

Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.

This Warranty does not apply where:

repairs have been made or attempted by others:

repairs are required because of normal wear and tear:

the tool has been abused, misused or improperly maintained:

alterations have been made to the tool.

IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.

MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY.

This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

EN0006-1

11

Image 11

Contents Hypoid Saw Scie hypoïde Sierra Circular English Original instructions SpecificationsPersonal safety Grounding Instructions Minimum gage for cord Ampere Rating Volts120 25 ft 50 ft 100 ft 150 ft More Than Not More Than AWGKickback causes and related warnings Circular SAW Safety WarningsDo not support board or panel away from the cut To avoid kickback, do support board or panel near the cutDo not TRY to Hold Short Pieces by Hand Bevel cutting Adjusting depth of cutSetting bevel angle Functional Description Assembly Rip fence Guide rule optional accessory MaintenanceReplacing carbon brushes Optional AccessoriesAdjusting for accuracy of 90 cut vertical cut Warranty Policy Makita Limited ONE Year WarrantySpécifications Français Mode d’emploi originalQue celles prévues peut entraîner une situation dangereuse Instructions DE Mise À LA Terre Consignes DE Sécurité Pour LA Scie CirculaireCauses du recul et avertissements connexes Précision ou un recul Avertissement Conservez CE Mode DemploiCoupe en biseau Description DU FonctionnementRéglage de la profondeur de coupe ViséeRangement de la clé hexagonale AssemblageCrochet Retrait ou pose de la lame Entretien Garde parallèle règle de guidage accessoire en optionUtilisation Remplacement des charbons Accessoires EN OptionPolitique de garantie Garantie Limitée D’UN AN MakitaEspañol Instrucciones originales EspecificacionesPage 16 a No se recomienda Advertencias DE Seguridad Para LA Sierra CircularMás de No más de Calibre del cable AWG 10 a 12 aNo apoye el tablero o panel alejado del corte Causas de los retrocesos y advertencias relacionadas¡NO Intente Sujetar Piezas Pequeñas a Mano Advertencia Guarde Estas InstruccionesAccionamiento del interruptor Corte en bisel Descripción DEL FuncionamientoAjuste de la profundidad de corte Guía visualAlmacenamiento de la llave de Allen hexagonal MontajeGancho Desmontaje o instalación del disco de sierra Ajuste para corte preciso de 90 corte vertical OperaciónMantenimiento Guía lateral Regla guía accesorio opcionalReemplazamiento de las escobillas de carbón Accesorios OpcionalesPolítica de garantía Garantía Limitada Makita DE UN AÑOPage Page Advertencia