Makita 5377MG-R Functional Description, Adjusting depth of cut, Bevel cutting, Positive stopper

Page 7

USD101-2

Symbols

The followings show the symbols used for tool.

･volts

･amperes

･hertz

･ alternating current

･no load speed

･ revolutions or reciprocation per minute

FUNCTIONAL DESCRIPTION

CAUTION:

•Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool.

Adjusting depth of cut

1. Lever

1

007393

CAUTION:

•After adjusting the depth of cut, always tighten the lever securely.

Loosen the lever on the depth guide and move the base up or down. At the desired depth of cut, secure the base by tightening the lever.

For cleaner, safer cuts, set cut depth so that no more than one blade tooth projects below workpiece. Using proper cut depth helps to reduce potential for dangerous KICKBACKS which can cause personal injury.

Bevel cutting

Positive stopper

22.5	51.5	1
		1

45

51.5

22.5

45

2

007394

1.Lever

2.Positive stopper

Turn the positive stopper so that the arrow on it points one of three positions (22.5°,45°,51.5°). Then, tilt the tool base until it stops and secure the base with the lever. At this time, the same angle as the one that the arrow points is obtained.

Setting bevel angle

Loosen the lever and tentatively set the tool base at the 0°bevel angle, then tighten the lever securely.

Turn the positive stopper so that the arrow on it points one of three positions (22.5°,45°,51.5°) that is equal to or greater than the desired bevel angle.

Loosen the lever again and then tilt and secure the tool base at the desired angle securely.

7

Image 7

Contents Hypoid Saw Scie hypoïde Sierra Circular Personal safety SpecificationsEnglish Original instructions Grounding Instructions Minimum gage for cord Ampere Rating Volts120 25 ft 50 ft 100 ft 150 ft More Than Not More Than AWGKickback causes and related warnings Circular SAW Safety WarningsDo not support board or panel away from the cut To avoid kickback, do support board or panel near the cutDo not TRY to Hold Short Pieces by Hand Bevel cutting Adjusting depth of cutSetting bevel angle Functional DescriptionAssembly Rip fence Guide rule optional accessory MaintenanceAdjusting for accuracy of 90 cut vertical cut Optional AccessoriesReplacing carbon brushes Warranty Policy Makita Limited ONE Year WarrantySpécifications Français Mode d’emploi originalQue celles prévues peut entraîner une situation dangereuse Instructions DE Mise À LA Terre Consignes DE Sécurité Pour LA Scie CirculaireCauses du recul et avertissements connexes Précision ou un recul Avertissement Conservez CE Mode DemploiCoupe en biseau Description DU FonctionnementRéglage de la profondeur de coupe ViséeCrochet Retrait ou pose de la lame AssemblageRangement de la clé hexagonale Utilisation Garde parallèle règle de guidage accessoire en optionEntretien Remplacement des charbons Accessoires EN OptionPolitique de garantie Garantie Limitée D’UN AN MakitaEspañol Instrucciones originales EspecificacionesPage 16 a No se recomienda Advertencias DE Seguridad Para LA Sierra CircularMás de No más de Calibre del cable AWG 10 a 12 aNo apoye el tablero o panel alejado del corte Causas de los retrocesos y advertencias relacionadas¡NO Intente Sujetar Piezas Pequeñas a Mano Advertencia Guarde Estas InstruccionesAccionamiento del interruptor Corte en bisel Descripción DEL FuncionamientoAjuste de la profundidad de corte Guía visualGancho Desmontaje o instalación del disco de sierra MontajeAlmacenamiento de la llave de Allen hexagonal Ajuste para corte preciso de 90 corte vertical OperaciónMantenimiento Guía lateral Regla guía accesorio opcionalReemplazamiento de las escobillas de carbón Accesorios OpcionalesPolítica de garantía Garantía Limitada Makita DE UN AÑOPage Page Advertencia