Milwaukee 6480-20 Operation, Adjusting the Blade Perpendicularity, Cross-Cutting, Changing Blades

Page 8

Step 4 - Adjusting the Blade -

Perpendicularity

If you remove the saw motor without making sure that the factory-set adjustment screw contacts the plate on the saw motor, then the blade will not be perpendicular (90°) to the workpiece, possibly resulting in inac- curate cuts.

1.Unplug the tool.

2.To adjust for perpendicularity, loosen the two mounting nuts on the front of the saw motor. The adjustment screw is located to the right of these nuts (Fig. 13).

3.Loosen the lock nut under the bracket. Tighten or loosen the adjustment screw depending on the angle adjustment required. ONLY make slight adjust- ments.

4.Tighten the lock nut, making sure the screw is against the upright plate.

5.Tighten the two hex nuts to secure the saw.

6.Plug in the tool and make a sample cut. Repeat the procedure if necessary.

WARNING

Do not cut a workpieces that has a width smaller than that of the saw carriage. Proper support for the workpiece must be maintained to insure safety. When the carriage moves over the workpiece, it would be impossible to safely support the workpiece for the cut. Use a tool bet- ter suited for these applications.

Cross-Cutting

A cross-cut is a vertical cut that must always be done from the top to the bottom of a workpiece.

Making the Cut:

1.

Rotate the saw motor to the cross-cut-

 

ting position (Fig. 14). To rotate the

 

motor, pull out the indexing pins and

 

rotate the saw motor. Lock the indexing

 

pins into the preset holes on the saw

 

carriage. The pins are spring-loaded

 

and should snap into place.

2.

Loosen the carriage lock and allow

 

the saw motor to raise to the top of the

 

tool. The saw motor is attached to the

 

counterbalance cable and should raise

 

to the top of the guide tubes by itself. If it

 

does not, see “Lubricating Guide Tubes”

 

in the Maintenance section.

3.

Plug in the tool.

4.

Place the workpiece on the rollers. Do

 

not to drop the material; this may knock

OPERATION

MILWAUKEE recommends using the Hold Down Bar Kit for frequent cutting of workpiec- es thinner than 1/4" (see "Accessories").

the rollers out of alignment or damage

the rollers.

Slide the workpiece to the desired

WARNING

To reduce the risk of injury, wear safety goggles or glasses with side shields. Unplug the tool before changing accessories or making adjustments.

Selecting a Blade

A Combination/Rip blade is supplied with the tool.

MILWAUKEE recommends using one of the blades listed in “Accessories". These blades will provide the best tool performance and the best cut. Always keep blades clean and sharp for the best performance. A dull or dirty blade can bind and pinch, resulting in kick back or a poor cut.

Changing Blades

1.Unplug the tool.

2.Remove the blade guard (see "Installing the Blade Guard").

3.To remove the bolt from the spindle, use the wrench provided with the tool to turn the bolt counterclockwise while holding in the spindle lock button.

4.Remove the outer flange, blade, and inner flange. Clean the spindle, flanges, bolt and blade to remove buildup of dust and debris.

5.Replace the inner flange.

6.Install the blade with the arrow pointing counterclockwise.

7.Replace the outer flange. Tighten the bolt clockwise using the wrench pro- vided while holding in the spindle lock button.

8.Install the blade guard (see "Installing the Blade Guard").

NOTE: It may be necessary to readjust the rulers after changing or resharpening blades (see “Adjusting the Rulers”).

WARNING

To reduce the risk of injury, make sure the tool is OFF before plugging in the tool.

Starting and Stopping the Motor

1.To start the saw motor, lift the switch up. The switch will stay up until it is pushed down.

2.To stop the saw motor, push the switch down.

The workpiece must be supported by a mini- mum of two rollers. When using the Midway Fence Kit , material must extend at least 4" beyond the saw carriage on either side.

For easier cutting and best performance, MILWAUKEE recommends using an Exten- sion Kit when cross-cutting workpieces that extend beyond the blade by 5' or more on one side. Do not cross-cut workpieces that exceed 8'.

WARNING

To reduce the risk of injury, do not place hands on or under saw carriage or in the path of the saw blade.

Fig. 14

Indexing pins

Cross-cut ruler

 

position using the cross-cut ruler as a

 

measure.

5.

Start the motor and allow it to reach full

 

speed before beginning the cut.

6.

When the motor has reached full speed,

 

slowly pull the saw motor down through

 

the workpiece, keeping your hand on the

 

handle.

7.

Once the cut is complete, turn the tool

 

off and wait for the blade to come to a

 

complete stop.

8.

Raise the saw motor and allow the saw

 

motor to return to the top of the guide

 

tubes.

9.

Tighten the carriage lock.

 

NOTE: A coasting blade can mar the

 

edge of a freshly cut workpiece.

WARNING

Do not cut a workpieces that has a width smaller than that of the saw carriage. Proper support for the workpiece must be maintained to insure safety. When the carriage moves over the workpiece, it would be impossible to safely support the workpiece for the cut. Use a tool bet- ter suited for these applications.

14

15

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 6480-20 General Safety Rules Read ALL Instructions Work Area SafetyElectrical Safety Personal SafetySpecifications Specific Safety RulesSymbology Extension Cords Functional DescriptionGrounding Tool Assembly Installing the Cord Keeper Installing BladesAdjusting the Rulers Adjusting the Rollers Adjusting the Blade ParallelismPanel Saw Alignment Line up on 36 markAdjusting the Blade Perpendicularity OperationCross-Cutting Selecting a BladeMaintenance Accessories Five Year Tool Limited WarrantySécurité Électrique Conserver CES Instructions Sécurité DES PersonnesUtilisation ET Entretien DES Outils Aire DE Travail Réparation Règles DE Sécurité ParticulièreDescription Fonctionnelle Mise a LA Terre SpécificationsNo de Volts CapacitéCordons DE Rallonge Montage DE Loutil PictographieRéglage des règles Installation des lamesMontage du moteur de scie Installation de la protection de lame Montage du range-cordonAlignement de la scie à panneau Étape 1 Réglage des rouleauxManiement Étape 2 Réglage des tubes de guidageÉtape 3-Réglage de la lame-Parallélisme Étape 4 Réglage de la lame Perpen- dicularitéCoupe transversale Coupe longitudinaleGoupille de PositionnementAccessoires Avertissement Entretien de l’outil Lubrification des tubes de guidageNettoyage RéparationsGuarde Estas Instrucciones Seguridad Personal Seguridad EléctricaConsulte la sección Corte longitudinal ServicioReglas Especificas DE Seguridad Extensiones Electricas TierraSimbología EspecificacionesDescripcion Funcional Ensamblaje DE LA Herramienta Orden de montajeColocación del soporte Instalación del contrapesoApriete la traba del soporte móvil Montaje del motor de la sierraInstalación de la cuchilla Cuchilla De la Sierra Brida Perno externaInstalación de la guarda de la cuchilla Paso 1 Ajuste de los rodillosAlineación de la sierra para tableros La marca de los 914 mmOperacion Paso 2 Ajuste de los tubos guíaPaso 4 Ajuste de la cuchilla Perpen- dicularidad Paso 3 Ajuste de la cuchilla Paralel- ismoArranque y paro del motor Corte transversalCorte longitudinal Regla para cortes longitudinalesAccesorios Advertencia Mantenimiento Garantía Limitada DE Cinco Años Advertencia Mantenimiento de las herramientasLubricación de los tubos guía ReparacionesCanada Service Milwaukee Milwaukee800.729.3878 800.729.3878 fax
Top Page Image Contents