Milwaukee 6088-20, 6086-20, 6082-20, 6081-20, 6080-20, 6089-20 manual Using Type 1 Cut-Off Wheels Fig

Page 10

WARNING!

A Type 1 guard must be installed when using a Type 1 cut- off wheel to provide maximum protection for the operator if the wheel should break.

Installing and Removing Type 1 Guard Assembly and Adjusting Shoe (Fig. 12)

Fig. 12

Carriage bolt and wingnut

Guard

Guard screw

Adjusting shoe

Spindle

1.Unplug tool and place it upside down on a level surface. Remove any accessories from spindle.

2.Loosen the guard screw and slip the guard over the spindle.

Position the guard in the location which offers best control and guard protection. For operating zones that provide maximum protection for the operator, see Fig. 9. Tighten the guard screw securely.

3.To adjust the guard, unplug the tool, loosen the guard screw, rotate the guard to the desired position and retighten the guard screw.

4.To remove the adjusting shoe, loosen the wing nuts, slide the shoe over to the access holes and lift out. To install the adjusting shoe, insert the head of the carriage bolts into guard access holes and slide the shoe over to the far edge of slots. Adjust shoe to desired position and tighten wing nuts securely.

5.To remove the guard, unplug the tool, remove the accessories and reverse the procedure.

Using Type 1 Cut-Off Wheels (Fig. 13)

1.Firmly grasp rear handle and side handle before starting and while us- ing tool. Allow wheel to come to full speed before starting.

2.When using a cut-off wheel, hold tool as shown, using only the edge of the wheel (Fig. 13).

Fig. 13

3.Control pressure and surface contact between wheel and workpiece. Too much pressure slows cutting speed.

WARNING!

To reduce the risk of injury, never use a Type 1 cut-off wheel for surface grinding.

page 10

Image 10

Contents Operators Manual Manuel DE Lutilisateur Manual DEL Operador Personal Safety Electrical SafetyService Functional Description Specific Safety Rules Sanders and GrindersSpindle Grounding Guidelines for Using Extension CordsRecommended Minimum Wire Gauge For Extension Cords ExtensioncordsTool Assembly Installing the Side HandleOperation Adjusting the Rear Handle Position Fig Select ModelsSanding Disc and Grinding Wheel Material Using Sanding Discs Installing Grinding Wheels Fig Using Grinding and CUT-OFF WheelsInspecting Wheels Selecting Wheels Using Type 1 Cut-Off Wheels Fig Using Wire Brushes Selecting Wire BrushesFive Year Tool Limited Warranty MaintenanceAccessories RepairsSécurité Individuelle Conservercesinstructions Sécurité DU Lieu DE TravailSécurité Électrique UTILISATIONETENTRETIENDEL’OUTILÉLECTRIQUERègles DE Sécurité Particulière Description FonctionnelleCordonsderallonge Calibres minimaux recommandés pour Les cordons de rallongeMise À LA Terre Avertissement Directives pour l’emploi des cordons de rallongeMontage DE Loutil Avertissement Pose de la poignée latéralePositionnement de la poignée Fig Certains Modèles Maniement AvertissementComposants des disques abrasifs et des meules Utilisation DES Disques Abrasivs Choix des disques abrasifs et des grains Installation de la meule FigUtilisation DES Meules Abrasives ET DES Meules À Tronçonner Corindon Aluminium-Zircone CéramiqueInspection des meules Utilisation des meules à tronçonner de type 27 Fig Utilisation des meule à tronçonner de type 1 FigUtilisation DES Brosses À Fils Dacier Sélection des brosses à fils d’acierGarantie Limitée DE L’OUTIL DE Cinq ANS Maintenance AvertissementAccessoires Avertissement RéparationsSeguridad Personal GUA0RDEESTASINSTRUCCIONES Seguridad EN EL Área DE TrabajoSeguridad Eléctrica USO Y Cuidado DE LAS Herramientas EléctricasReglas Especificas DE Seguridad Lijadoras Y Esmeriladoras SimbologíaEspecificaciones Descripcion FuncionalExtensióneseléctricas Tierra ¡ADVERTENCIAGuías para el uso de cables de extensión Ensambaje DE LA Herramienta ¡ADVERTENCIA Instalación del mango lateralBloqueo del gatillo Fig Modelos seleccionados Operacion ¡ADVERTENCIAMaterial de discos abrasivos y ruedas abrasivas USO DE Discos Abrasivos Óxido Aluminio y Circona de Cerámica USO DE Ruedas Abrasivas Y Ruedas DE CorteSelección de discos abrasivos y granos Instalación de ruedas abrasivas FigSolución de problemas Revisión de las ruedasUso de las ruedas de corte tipo 1 Fig Usando DE Cepillos DE Alambre Selección de cepillos de alambreGarantía Limitada DE Cinco Años Mantenimiento ¡ADVERTENCIAAccesorios ¡ADVERTENCIA Mantenimiento de las herramientasSawdust