Lincoln 500 manual Commander / K867 / LN-8 Connection Diagram

Page 40

COMMANDER / K867 / LN-8 CONNECTION DIAGRAM

WARNING

Do not operate with panels open.	Keep guards in place.
Disconnect NEGATIVE (-) BATTERY LEAD	Keep away from moving parts.
before servicing.	Only qualified personnel should install,use
Do not touch electrically live parts.	or service this equipment.

CONNECTION DIAGRAM

F-6

Vantage 500 CUMMINS

ELECTRODE

TO WORK

14PIN AMPHENOL

K867 UNIVERSAL

ADAPTER PLUG

SPARE 82 81 42 41

31

32

2

4

21 GND

}N.C.

31

32

2

4

21

GND

LN-8

WIRE

FEEDER

K196

INPUT CABLE

DIAGRAMS

TO WORK

ELECTRODE CABLE

TO WIRE FEED UNIT

CAUTION :

75

76

77

	A
}	B
	C

N.D.

ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE

AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE

DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN

THE ENGINE WELDER OPERATING MANUAL.

N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE

APPICATIONS. SEE OPERATING MANUAL.

N.B. USE VOLTMETER SWITCH TO SELECT DESIRED ELECTRODE POLARITY. POSITION THE SELECTOR SWITCH TO "WIRE WELDING CV".

N.C. INSULATE EACH UNUSED LEAD INDIVIDUALLY.

N.D. SPLICE LEADS AND INSULATE.

7-2000

S23989

F-6

Image 40

Contents Vantage 500 Cummins Safety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion Précautions DE Sûreté Thank You Table of Contents Vii Installation Input Diesel EngineSafety Precautions Location / VentilationStoring StackingHigh Temperature Operation LiftingHigh Altitude Operation TowingPRE-OPERATION Engine Service Battery Connection OILEngine Coolant Fuel USE Diesel Fuel onlyWelding Terminals Remote Control Auxiliary Power ReceptaclesStandby Power Connections OutputFigure A.2 Connection of the Vantage to Premises Wiring Connection of Lincoln Electric Wire Feeders Connection of AN LN-23P Wire Feeder to the VantageConnection of LN-7, LN-8 or LN-742 to the Vantage Connection of LN-15 to the VantageConnection of the LN-25 to the Vantage Connection of Prince XL Spool GUN to the VantageOperation Safety InstructionsGeneral Description Controls and Settings Battery Charging Light Idler SwitchOIL Pressure Gauge Engine ProtectionAuxiliary Power Controls Starting the Engine Engine OperationStopping the Engine Engine BREAK-IN BREAK-IN PeriodWelder Operation Vantage Settings When Using the K930-2 TIG Module For Tungsten ElectrodesAuxiliary Power Operation Operation Optional Field Installed Accessories AccessoriesK767-2 Four Wheeled Steerable Yard Trailer Routine and Periodic Maintenance MaintenanceEngine Maintenance Fuel Filters Battery HandlingCooling System Welder / Generator Maintenance Troubleshooting HOW to USE Troubleshooting GuideMisadjustments Course of Action Possible Areas RecommendedFunction Problems Possible AreasProblems Possible Areas Diagrams Vangage 500 Cummins Wiring DiagramDIAGRAMSF-2 Connection DiagramCommander / K867 / K775 / LN-7 Connection Diagram DiagramDiagrams Diagrams Commander / K867 / LN-8 Connection Diagram Diagrams Diagrams Engine Welders /LN-8 Connection Diagram ConnectionDiagrams Diagrams Diagrams Diagrams Dimension Print M18962-3Precaucion l Aviso DE