Craftsman 919.19541 owner manual Motor, Pressure Switch Replacement, To Replace Regulator

Page 21

Motor

This motor has a manual thermal overload protector. If the motor over- heats for any reason, the overload protector will shut off the motor. The motor must be allowed to cool down before restarting. To restart:

1.Place the On/Auto/Off lever in the Off postion.

2.Allow the motor to cool.

Reset

Button

3.Depress the red reset button on the motor.

4.Place the On/Auto/Off lever in the On/Auto postion to restart the motor.

Pressure Switch - Replacement

Pressure loads beyond design lim-

its may cause tank rupture or explosion. Pressure switch opera- tion is related to motor HP, tank rating, and safety valve setting. Do not attempt to adjust, remove, or defeat the pressure switch, or change and modify any pressure control related device. If replace- ment is necessary the same rated switch must be used. Contact a trained service technician for replacement.

To Replace Regulator

1.Release all air pressure from air tank. See “To Drain Tank” in the Maintenance section.

2.Unplug air compressor.

3.Remove the regulator ring and remove the console cover.

Regulator

Cover

Ring

 

4.Using an adjustable wrench loosen pressure relief tube nut at air tank and pressure switch.

5.Lift retaining clip from handle and remove handle.

Retaining clip

Handle

6.Using an adjustable wrench, rotate the pressure switch assembly as shown.

Tank

RegulatorPressure

Gauge

Outlet

Quick

Pressure

Connect

Gauge

 

 

 

7.Remove the outlet pressure gauge, tank pressure gauge, and quick connect (if equipped) from the regulator.

8.Remove the regulator.

9.Apply pipe sealant tape to the nipple.

21- ENG

D24910

Image 21
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A AIR CompressorTable of Contents Specification Table Safety Guidelines DefinitionsImportant Safety Instructions What Could Happen HazardAttachments & Accessories Hazard Belt can cause serious injury if they Never operate the compressor withFire, Inhalation, Damage to Vehicle Surfaces Accessories AccessoriesGlossary Duty CycleContents of Carton AssemblyTools Required for Assembly To Install HandleTo Assemble Wheels Assemble Rubber FeetTo Add Oil To Pump To Add Oil InstallationAir Compressor Location Before removing the oil fill cap or oil drain plugVoltage and Circuit Protection Extension CordsKnow Your Air Compressor OperationBefore First Start-up How to Use Your Unit How to StopBreak-in Instructions Pressure Release Valve Check ValveBefore Each Start-Up How to StartCustomer Responsibilities MaintenanceTo Drain Tank To Check Safety ValveOil ChangingAir Filter Inspection Replacement Motor Pulley/Flywheel AlignmentAir Compressor Pump Intake and Exhaust Valves To Replace or Clean Check Valve Service and AdjustmentsOutlet Tube Pressure Relief Tube Nuts Nuts Check Valve Screwdriver Open position nothing is visiblePressure Switch Replacement MotorTo Replace Regulator To Replace Belt Regulator ArrowWing Nut Storage Problem Cause Correction TroubleshootingPressure reading Minal box area Problem Cause Correction Garantía ContenidoModelo Nº 919-195410 Definiciones DE Normas DE SeguridadResultar en lesiones menores o ModeradasGuarde Estas Instrucciones Instrucciones Importantes DE SeguridadAgregados Y Accesorios Tros de acuerdo a los códigos eléctricos Advertencia Riesgo DE Quemaduras ¿QUÉ Puede OCURRIR? Advertencia Riesgo DE Operación Insegura ¿QUÉ Puede OCURRIR? Accesorios GlosarioCiclo DE Servicio AccesoriosContenido de la caja EnsambladoHerramientas necesarias para el ensamble DesempaqueEnsamble de las patas de caucho Ensamble de las ruedasPara agregar aceite a la bomba TuercaPara agregar aceite InstalaciónUbicación del compresor de aire EnchufeProtección del voltaje y del circuito Cables de extensión eléctricaConozca su compresor de aire OperaciónAntes del primer arranque Cómo utilizar su unidadInstrucciones para el asentamiento Cómo detenerlaCómo poner en marcha Antes de cada puesta en marchaResponsabilidades del cliente MantenimientoAceite Cómo verificar la válvula de seguridadCómo drenar el tanque VerificaciónPolea y volante Alineación Filtro de Aire Inspección y reemplazoPara reemplazar o limpiar la válvu La de retención Servicio Y AjustesTubo de salida Tuercas TuercasVálvula reguladoraPara volver a arrancar MotorPara reemplazar el regulador Interruptor de presión ReemplazoCambio de la correa Regulador FlechaTuerca mariposa Almacenaje Problema Causa Corrección Guía DE Diagnóstico DE ProblemasOperación. Nota Ajuste la presión Retire y limpie, o reemplace 57- SP D24910 D24910 58- SP 59- SP D24910 Get it fixed, at your home or ours