Craftsman 919.19541 owner manual To Replace Belt, Regulator Arrow, Wing Nut

Page 22

10.Assemble the regulator and ori- ent as shown in previous figure.

NOTE: Arrow indicates flow of air. Make sure it is pointing in the direc-

Regulator

Arrow

tion of air flow.

11.Reapply pipe sealant to outlet pressure gauge, tank pressure gauge, and quick connect.

12.Reassemble outlet pressure gauge,tank pressure gauge, and quick connect. Orient outlet pressure gauge and tank pres- sure gauge to read correctly. Tighten quick connect with wrench.

13.Rotate pressure switch assembly into correct position.

14.Replace console cover and regu- lator ring.

15.Replace handle. Refer to Handle Assembly paragraph in the Assembly section.

To Replace Belt

Serious injury or damage may occur

if parts of the body or loose items get caught in moving parts. Never operate the unit with the belt guard removed. The belt guard should be removed only when the compres- sor is unplugged.

1.Place the ON/AUTO-OFF lever in the OFF position.

2.Unplug compressor.

3.Remove the front of the belt guard by disengaging the snaps. Insert a flat bladed screwdriver at each snap location and pry the beltguard apart.

4.Loosen the wing nut on hold down plate and tilt motor to allow for easy removal or instal- lation of the belt.

Wing Nut

5.Remove belt.

6.Replace belt. NOTE: The belt must be centered over the grooves on the flywheel and motor pulley.

7.Turn the wing nut on the hold down plate until it makes contact with the washer, plus one addi- tional turn.

8.Replace the belt guard.

D24910

22- ENG

Image 22
Contents AIR Compressor Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.ATable of Contents Safety Guidelines Definitions Specification TableImportant Safety Instructions Hazard What Could HappenAttachments & Accessories Hazard Never operate the compressor with Belt can cause serious injury if theyFire, Inhalation, Damage to Vehicle Surfaces Glossary AccessoriesAccessories Duty CycleTools Required for Assembly AssemblyContents of Carton To Install HandleAssemble Rubber Feet To Assemble WheelsTo Add Oil To Pump Air Compressor Location InstallationTo Add Oil Before removing the oil fill cap or oil drain plugExtension Cords Voltage and Circuit ProtectionOperation Know Your Air CompressorBreak-in Instructions How to Use Your Unit How to StopBefore First Start-up Pressure Release Valve Check ValveHow to Start Before Each Start-UpMaintenance Customer ResponsibilitiesOil To Check Safety ValveTo Drain Tank ChangingMotor Pulley/Flywheel Alignment Air Filter Inspection ReplacementAir Compressor Pump Intake and Exhaust Valves Outlet Tube Pressure Relief Tube Nuts Nuts Check Valve Service and AdjustmentsTo Replace or Clean Check Valve Screwdriver Open position nothing is visibleMotor Pressure Switch ReplacementTo Replace Regulator Regulator Arrow To Replace BeltWing Nut Storage Troubleshooting Problem Cause CorrectionPressure reading Minal box area Problem Cause Correction Contenido GarantíaResultar en lesiones menores o Definiciones DE Normas DE SeguridadModelo Nº 919-195410 ModeradasInstrucciones Importantes DE Seguridad Guarde Estas InstruccionesAgregados Y Accesorios Tros de acuerdo a los códigos eléctricos Advertencia Riesgo DE Quemaduras ¿QUÉ Puede OCURRIR? Advertencia Riesgo DE Operación Insegura ¿QUÉ Puede OCURRIR? Ciclo DE Servicio GlosarioAccesorios AccesoriosHerramientas necesarias para el ensamble EnsambladoContenido de la caja DesempaquePara agregar aceite a la bomba Ensamble de las ruedasEnsamble de las patas de caucho TuercaUbicación del compresor de aire InstalaciónPara agregar aceite EnchufeCables de extensión eléctrica Protección del voltaje y del circuitoOperación Conozca su compresor de aireInstrucciones para el asentamiento Cómo utilizar su unidadAntes del primer arranque Cómo detenerlaAntes de cada puesta en marcha Cómo poner en marchaMantenimiento Responsabilidades del clienteCómo drenar el tanque Cómo verificar la válvula de seguridadAceite VerificaciónFiltro de Aire Inspección y reemplazo Polea y volante AlineaciónTubo de salida Servicio Y AjustesPara reemplazar o limpiar la válvu La de retención Tuercas TuercasVálvula reguladoraPara reemplazar el regulador MotorPara volver a arrancar Interruptor de presión ReemplazoRegulador Flecha Cambio de la correaTuerca mariposa Almacenaje Guía DE Diagnóstico DE Problemas Problema Causa CorrecciónOperación. Nota Ajuste la presión Retire y limpie, o reemplace 57- SP D24910 D24910 58- SP 59- SP D24910 Get it fixed, at your home or ours