Tripp Lite APSX2012SW Battery Voltage LED, Voltage Setting Switch, Search Mode Setting Switch

Page 5

1. Overview and Features

1.2.7 Battery Voltage (LED 5-8)

LED 5-8 indicate the battery capacity as detailed in the following table:

Battery Voltage

LED 5

LED 6

LED 7

LED 8

25%

On

50%

On

On

75%

On

On

On

 

 

 

 

 

100%

On

On

On

On

 

 

 

 

 

1.2.8 Voltage Setting (Switch 1-3)*

Switch

ON

OFF

 

 

 

DC-to-AC Transfer Delay (Switch 1)

30 sec (Default)

5 sec

Low Battery Alarm (Switch 2)

11.2V

10.9V (Default)

AC Transfer Voltage (Switch 3)

190V

170V (Default)

* Notes:

1.Switches are located farthest from the battery temperature port. See diagram on page 3.

2.The switches must be set before the system is turned on.

3.Switch 2 sets the low battery voltage alarm level (at higher voltage setting, alarm will sound sooner).

4.Switch 3 sets the low-level AC-to-DC voltage point. If the AC input voltage decreases to below the setpoint, the inverter will automatically switch to DC MODE. See the following table for details.

Nominal Voltage

Low Voltage Transfer Point (AC-to-DC)

Return Voltage Point (DC-to-AC)

230V

On

190

200

 

 

 

Off

170

180

 

 

 

 

 

1.2.9 Search Mode Setting (Switch 4)

Search Mode activates when the unit is operating in inverter mode (battery power) to prevent unnecessary battery discharge when electrical power is not required. If the inverter is supporting loads that must constantly be powered, turn off switch 4 to disable Search Mode.

Switch 4

 

 

Search Mode

Function

 

 

 

 

 

 

 

ON

 

 

Enable

Inverter turns on only if load is >100W

OFF (Default)

 

 

Disable

Inverter always on if AC power is absent

1.2.10 Floating Voltage/Battery Type (Switch 5)

 

 

 

 

 

 

 

 

 

Switch 5

 

Floating Voltage

Acceptance Voltage

 

Battery Type

ON (Default)

 

13.8V

14.5V

 

Absorbed Glass Mat (AGM)

OFF

 

13.2V

13.8V

 

Wet-Cell

 

 

 

 

 

 

 

Note: The unit will charge the battery to acceptance voltage, continue for 1 to 12 hours, then drop to floating voltage.

5

201110117 93-3054.indb 5

11/9/2011 10:57:55 AM

Image 5
Contents Sine Wave DC-to-AC Inverter/Chargers Important Safety Instructions Indicators, Controls and Settings Overview and FeaturesControls and LED Indicators OverviewDC Mode Inverter LED Power ON/OFF ButtonAC Mode Charger LED Battery Limits LEDVoltage Setting Switch Battery Voltage LEDSearch Mode Setting Switch Floating Voltage/Battery Type SwitchBattery Battery ChargerExample Match Battery Amp-Hour Capacity to Your ApplicationBattery Installation Monthly MaintenanceBattery Connection Battery LocationVolt Main Battery Connection Terminal DC Side4. Installation and Operation Installation and OperationInstallation Installation Diagrams and ChartsInstallation and Start-Up Technical SpecificationsService TroubleshootingCargador de batería Modelos APSX1012SW, APSX2012SW 12V CC a 230V CAInstalación y mantenimiento De la batería Convertidor/cargador Instalación y funcionamiento¡GUARDE Estas Instrucciones Instrucciones de seguridad importantesVisión de conjunto y características Indicadores, controles y configuracionesVisión de conjunto Controles e indicadores LEDModo convertidor CC LED 2 Botón Power ON/OFF de encendido/apagadoModo cargador CA LED Estado de convertidor LEDConfiguración del modo de búsqueda interruptor Configuración del voltaje interruptoresVoltaje de la batería LED Voltaje Flotante/ Tipo de Batería InterruptorBatería Cargador de bateríaEjemplo Instalación de la batería Mantenimiento mensualConexión de la batería Cerramiento de la bateríaConexión de la batería principal de 12 voltios Instalación Diagramas y gráficos de instalaciónInstalación y funcionamiento Instalación y puesta en marcha Especificaciones técnicasRegistro DE LA Garantía Solución de problemasServicio Dépannage Modèles APSX1012SW, APSX2012SW 12V CC à 230V CAChargeur de batterie Caractéristiques techniques Conservez CES Instructions Consignes importantes de sécuritéVue d’ensemble Vue d’ensemble et CaractéristiquesIndicateurs, contrôles et réglages Contrôles et indicateurs DELDC Mode Inverter Onduleur en mode CC DEL Bouton Power ON/OFF marche/arrêtAC Mode Charger Chargeur en mode CA DEL Battery Limits Limites de la batterie DELVoltage Setting Réglages de tension Commutateurs Battery Voltage Tension de la batterie DEL9 Réglage du mode Recherche Commutateur Tension d’égalisation/Type de batterie CommutateurBatterie Chargeur de batterieExemple Emplacement de la batterie Installation de la batterieEntretien mensuel Raccordement de la batterieMaison de 12 Volts Schémas et tableaux relatifs à l’installation Installation et fonctionnementBorne côté CC4. Installation and Operation Caractéristiques techniques Installation et démarrageEnregistrement DE LA Garantie DépannageRéparation Выявление и устранение Зарядное устройство Неисправностей Модели APSX1012SW, APSX2012SW 12B DC-в-230B ACСохраните ЭТИ Инструкции Важные инструкции по технике безопасностиОбзор Обзор и функцииИндикаторы, регулирующие устройства и настройки 1 Регулирующие устройства и светодиодные индикаторыЗвук Светодиодные и звуковые индикаторы2 Кнопка Вкл/Выкл ON/OFF 3 Преобразователь в режиме DC ИНДНапряжение аккумулятора 7 Напряжение аккумулятора ИНД8 Установка напряжения Переключатели Переключатель АC-в-DC DC-в-АСАккумулятор Аккумуляторное зарядное устройство2 Уровень недостаточности Пример468 амп-часов ÷ 40 амп Номинал Преобразователя/зарядногоПодсоединение аккумулятора Ежемесячное техническое обслуживаниеУстановка аккумулятора Подсоединение основного аккумулятора на 12 вольт Установка и эксплуатация 2 Клемма сторона DC4. Installation and OperationУстановка Установочные схемыУстановка и запуск СпецификацииМодель СпецификацияРегистрация Гарантии Выявление и устранение неисправностейСервисное обслуживание

APSX2012SW, APSX1012SW specifications

The Tripp Lite APSX2012SW and APSX1012SW are cutting-edge power inverters designed for a variety of applications, particularly in environments where reliable power is critical. These devices convert DC power from a battery into AC power, enabling users to operate standard appliances and devices when access to traditional electrical outlets is limited.

One of the main features of the APSX2012SW is its 2000 watt continuous power output, with a surge capacity of up to 4000 watts, making it suitable for powering larger devices, including refrigerators and power tools. The APSX1012SW, on the other hand, delivers 1000 watts of continuous power with a surge capability of 2000 watts. These specifications ensure that users can run essential equipment seamlessly during emergencies or while camping.

Both models come equipped with built-in safety features to safeguard against overloading and overheating. The automatic shutdown feature protects the inverter and connected devices from damage, ensuring long-lasting performance. Additionally, the inverters include a cooling fan that activates only when necessary, minimizing noise while maintaining optimal operating temperatures.

Another noteworthy characteristic of the APSX series is its high-efficiency performance, reaching up to 90 percent efficiency under optimal conditions. This not only extends the operational life of your battery but also helps in conserving energy, making these inverters eco-friendly choices. Users will appreciate the inclusion of multiple outlets, useful for powering multiple devices simultaneously, and the inclusion of USB charging ports adds versatility for charging mobile devices.

The robust design of the APSX2012SW and APSX1012SW ensures durability in rugged environments. Their compact construction allows for easy transportation, making them ideal for outdoor activities, road trips, or in case of power outages at home. Both models also feature an LED display that provides vital information regarding battery status and output levels, helping users monitor system performance effectively.

In conclusion, the Tripp Lite APSX2012SW and APSX1012SW power inverters stand out for their reliable performance, advanced safety features, and user-friendly design. Whether for camping, tailgating, or emergency situations, these inverters provide the perfect solution for anyone in need of portable power. Choose Tripp Lite for durable, efficient, and dependable power conversion solutions.