Tripp Lite APSX2012SW, APSX1012SW owner manual Volt Main Battery Connection

Page 9

3. Battery

Connect Fuse: NEC (National Electrical Code) article 551 requires that you connect all of your Inverter/Charger’s positive DC Terminals directly to a UL-listed fuse(s) and fuse block(s) within 18 inches of the battery. The fuse’s rating must equal or exceed the minimum DC fuse rating displayed on the Inverter/Charger’s nameplate. See diagrams below for proper fuse placement.

WARNING! • Failure to properly ground your Inverter/Charger to a vehicle’s chassis or earth ground may result in a lethal electrical shock hazard.

• Never attempt to operate your Inverter/Charger by connecting it directly to output from an alternator rather than a battery or battery bank.

Observe proper polarity with all DC connections.

3.4.2Non-Vehicular or Vehicular

Your Inverter/Charger’s Nominal DC Input Voltage must match the voltage of your battery or batteries—12 volts in most vehicular applications.

It is possible to connect your Inverter/Charger to the main battery within your vehicle’s electrical system. In most vehicles, the Inverter/ Charger will be connected to one or more dedicated auxiliary (house) batteries, isolated from the drive system to prevent possible draining of the main battery.

 

3

7

1

2

 

 

12 Volts

 

 

 

12 Volt Inverter/Charger

12 Volts

 

 

 

5

 

12 Volt Main Battery Connection

 

1

6

2

 

12 Volts

12 Volts

 

 

 

 

2

 

 

12 Volts

12 Volt Main and Auxiliary (House)

 

Battery Connection (Isolated Parallel)

4 7

12 Volt Inverter/Charger

3 5

112-Volt Alternator

2Vehicle Battery Ground

312-Volt Main Battery

412-Volt Auxiliary (House) Battery

5UL-Listed Fuse & Fuse Block (mounted within 18 inches of the battery)

6Battery Isolator

7Large Diameter Cabling

9

201110117 93-3054.indb 9

11/9/2011 10:57:57 AM

Image 9
Contents Sine Wave DC-to-AC Inverter/Chargers Important Safety Instructions Indicators, Controls and Settings Overview and FeaturesControls and LED Indicators OverviewDC Mode Inverter LED Power ON/OFF ButtonAC Mode Charger LED Battery Limits LEDVoltage Setting Switch Battery Voltage LEDSearch Mode Setting Switch Floating Voltage/Battery Type SwitchBattery Battery ChargerExample Match Battery Amp-Hour Capacity to Your ApplicationBattery Installation Monthly MaintenanceBattery Connection Battery LocationVolt Main Battery Connection Terminal DC Side4. Installation and Operation Installation and OperationInstallation Installation Diagrams and ChartsInstallation and Start-Up Technical SpecificationsService TroubleshootingCargador de batería Modelos APSX1012SW, APSX2012SW 12V CC a 230V CAInstalación y mantenimiento De la batería Convertidor/cargador Instalación y funcionamiento¡GUARDE Estas Instrucciones Instrucciones de seguridad importantesVisión de conjunto y características Indicadores, controles y configuracionesVisión de conjunto Controles e indicadores LEDModo convertidor CC LED 2 Botón Power ON/OFF de encendido/apagadoModo cargador CA LED Estado de convertidor LEDConfiguración del modo de búsqueda interruptor Configuración del voltaje interruptoresVoltaje de la batería LED Voltaje Flotante/ Tipo de Batería InterruptorBatería Cargador de bateríaEjemplo Instalación de la batería Mantenimiento mensualConexión de la batería Cerramiento de la bateríaConexión de la batería principal de 12 voltios Diagramas y gráficos de instalación Instalación y funcionamientoInstalación Instalación y puesta en marcha Especificaciones técnicasSolución de problemas ServicioRegistro DE LA Garantía Modèles APSX1012SW, APSX2012SW 12V CC à 230V CA Chargeur de batterie Caractéristiques techniquesDépannage Conservez CES Instructions Consignes importantes de sécuritéVue d’ensemble Vue d’ensemble et CaractéristiquesIndicateurs, contrôles et réglages Contrôles et indicateurs DELDC Mode Inverter Onduleur en mode CC DEL Bouton Power ON/OFF marche/arrêtAC Mode Charger Chargeur en mode CA DEL Battery Limits Limites de la batterie DELVoltage Setting Réglages de tension Commutateurs Battery Voltage Tension de la batterie DEL9 Réglage du mode Recherche Commutateur Tension d’égalisation/Type de batterie CommutateurBatterie Chargeur de batterieExemple Emplacement de la batterie Installation de la batterieEntretien mensuel Raccordement de la batterieMaison de 12 Volts Installation et fonctionnement Borne côté CC4. Installation and OperationSchémas et tableaux relatifs à l’installation Caractéristiques techniques Installation et démarrageDépannage RéparationEnregistrement DE LA Garantie Выявление и устранение Зарядное устройство Неисправностей Модели APSX1012SW, APSX2012SW 12B DC-в-230B ACСохраните ЭТИ Инструкции Важные инструкции по технике безопасностиОбзор Обзор и функцииИндикаторы, регулирующие устройства и настройки 1 Регулирующие устройства и светодиодные индикаторыЗвук Светодиодные и звуковые индикаторы2 Кнопка Вкл/Выкл ON/OFF 3 Преобразователь в режиме DC ИНДНапряжение аккумулятора 7 Напряжение аккумулятора ИНД8 Установка напряжения Переключатели Переключатель АC-в-DC DC-в-АСАккумулятор Аккумуляторное зарядное устройство2 Уровень недостаточности Пример468 амп-часов ÷ 40 амп Номинал Преобразователя/зарядногоЕжемесячное техническое обслуживание Установка аккумулятораПодсоединение аккумулятора Подсоединение основного аккумулятора на 12 вольт Установка и эксплуатация 2 Клемма сторона DC4. Installation and OperationУстановка Установочные схемыУстановка и запуск СпецификацииМодель СпецификацияВыявление и устранение неисправностей Сервисное обслуживаниеРегистрация Гарантии

APSX2012SW, APSX1012SW specifications

The Tripp Lite APSX2012SW and APSX1012SW are cutting-edge power inverters designed for a variety of applications, particularly in environments where reliable power is critical. These devices convert DC power from a battery into AC power, enabling users to operate standard appliances and devices when access to traditional electrical outlets is limited.

One of the main features of the APSX2012SW is its 2000 watt continuous power output, with a surge capacity of up to 4000 watts, making it suitable for powering larger devices, including refrigerators and power tools. The APSX1012SW, on the other hand, delivers 1000 watts of continuous power with a surge capability of 2000 watts. These specifications ensure that users can run essential equipment seamlessly during emergencies or while camping.

Both models come equipped with built-in safety features to safeguard against overloading and overheating. The automatic shutdown feature protects the inverter and connected devices from damage, ensuring long-lasting performance. Additionally, the inverters include a cooling fan that activates only when necessary, minimizing noise while maintaining optimal operating temperatures.

Another noteworthy characteristic of the APSX series is its high-efficiency performance, reaching up to 90 percent efficiency under optimal conditions. This not only extends the operational life of your battery but also helps in conserving energy, making these inverters eco-friendly choices. Users will appreciate the inclusion of multiple outlets, useful for powering multiple devices simultaneously, and the inclusion of USB charging ports adds versatility for charging mobile devices.

The robust design of the APSX2012SW and APSX1012SW ensures durability in rugged environments. Their compact construction allows for easy transportation, making them ideal for outdoor activities, road trips, or in case of power outages at home. Both models also feature an LED display that provides vital information regarding battery status and output levels, helping users monitor system performance effectively.

In conclusion, the Tripp Lite APSX2012SW and APSX1012SW power inverters stand out for their reliable performance, advanced safety features, and user-friendly design. Whether for camping, tailgating, or emergency situations, these inverters provide the perfect solution for anyone in need of portable power. Choose Tripp Lite for durable, efficient, and dependable power conversion solutions.