Hitachi C 8FSE specifications Relative standards, Laser marker only the Model C 8FSHE

Page 17

(4)Caution label (J) (at the front of the hinge) and caution labels (C) and (E) (at the front left of the turn table) (only the Model C 8FSHE)

Do not stare into laser beam. If your eye is exposed directly to the laser beam, it can be hurt. Caution

label (J) and caution labels (C) and (E) are adhered to each machine to comply with the standards for the safe use of laser equipment.

·Caution label (J) (at the front of the hinge) (only the Model C 8FSHE) Fig. 15-a

·Caution labels (C) and (E) (at the front left of the turn table) (only the Model C 8FSHE) For the U.S.A. and Canada

Fig. 15-b

For Europe, Australia, China and Asia

Fig. 15-c

C. Relative standards

Standards, regulations and guidelines for the safe use of laser equipment [The U.S.A.] FDA CDRH 21 CFR

[AUS/NZL] AS/NZS 2211.1: 2001

[Europe] EN 60825-1: 2001-11

D. Laser marker (only the Model C 8FSHE)

The Model C 8FSHE is equipped with the laser marker that complies with the Class II requirements of the standard specified in "Relative standards." The Class II laser is defined as follows:

·The laser power is low and it is safe by the protective measures such as blinking.

However, it is dangerous if the operator’s eyes are exposed directly to the laser for a protracted period.

·The operator can use the laser equipment without particular training and instruction.

·The amount of light exposure (output) is 1 mW or less at the position where the operator can be exposed to the laser radiation during operation. (This is in the case of the U.S.A. The measuring methods and the output values are different depending on the standards.)

The saw blade unit prevents access of the operator’s eye to the laser-emitting aperture less than 65 mm. In addition, the amount of light exposure (output) is 1 mW or less (about 0.4 mW) at this position. Thus the Model C 8FSHE satisfies the Class II requirements adequately. There is no ill effect on the operator’s body if looking at the laser line on the workpiece during operation.

-14-

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Models C 8FSE, C 8FSHE Remark Contents Laser marker Only the Model C 8FSHE Selling Point DescriptionsPositive angle stoppers Slide cutting Miter cutting Compound miter and bevel cutting Specifications Specifications· 216 mm 8-1/2 TCT saw blade 15.9 mm 5/8 bore, NT24 For Europe and others Except for the U.S.A and Canada Specification comparisonsComparisons with Similar Products C8FSE/C8FSHE 8FB2 Right angle For the U.S.A and CanadaFull-load current a 9.2 a Safety instructions Precautions in Sales PromotionPage Laser marker only the Model C 8FSHE Relative standardsAmbient illuminance and visibility of laser line Precautions concerning brakeConfirmation of saw blade lower limit position Adjustment and Operational PrecautionsConfirmation for use of sub fence Optional accessory Position adjustment of laser line Only the Model C 8FSHE Adjustment of table insert position How to use the vise assemblyCutting operation Page Bevel scale Clamp lever Tighten Crown molding stopper R Page Ball bushing Linear bearing Adjustment of ComponentsBevel angle adjustment Packing Turn table and base assy Precautions in disassembly and reassemblyRepair Guide Page Then remove the Lower Guard 215 from the Bearing Holder Lower guard, link, spindle assy and dust guidePage Armature assy and lock lever Page Vise ass’y Laser markerSpecial attention ReassemblyWiring diagram Page Page Page No-load current Reassembly requiring adjustmentChecking of insulation distance Product precision LubricationAdjustment of laser marker accuracy Page Page 211 Troubleshooting guideBushing 115 and slide Page 160 107 8FSHE Standard Repair Time Unit Schedules8FSE Slide Compound SAW 8FSHE 501 Parts SUB Fence For USA, can Nylon Clip Ball Bearing 608VVC2PS2L Standard Accessories Model C 8FSE 8FSE 162 153 152 8FSE Scale a For USA, can Carbon Brush 1 Pair For GBR 110V, USA, CAN, VEN, TPE Lock Lever Spring Includ 626
Top Page Image Contents