Hitachi C 8FSE, C 8FSHE specifications Lubrication, Product precision

Page 42

(3) Reassembly of the ball bushing

The Ball Bushing [114] and Holder (A) [124] are maintained at a smooth fit. When placing the Ball Bushing [114] into Holder (A) [124], gently hammer it with a plastic hammer so that the Ball Bushing [114] is seated into Holder (A) [124] in parallel. After reassembly, lubricate around the steel balls inside the Ball Bushing [114] with 2 grams of Nippeco SEP 3A grease. Apply machine oil to slide pipe (A) and slide pipe (B) of Hinge (A) Ass’y [87]. When reassembling, put the Ball Bushing [114] inside Holder (A) [124] as indicated in (A) of Fig. 55. Visual observation will do for this insertion. Layout in (A) offers about 30% higher rated load in (B).

Fig.55

6. Lubrication

Advise the customer to lubricate the machine as indicated below at least once a month. Also, prior to applying lubricant, any sawdust, dirt or other foreign matter should be thoroughly wiped away with a soft cloth.

(1)Swiveling section of the gear case

Coat machine oil on the swiveling and sliding portions of the Gear Case [198] and Hinge (A) Ass’y [87].

(2)Vise section

Coat machine oil on the screw thread portion of the Knob Bolt M10 x 66 [35] of the Vise Ass’y [42].

(3)Holder (A)

Coat machine oil on the swiveling and sliding portions of Holder (A) [124] and the Hinge Shaft (A) [9].

7. Product precision

On completion of reassembly, confirm precision tolerances.

Item

Tolerance

Deflection of dummy disc

0.15/φ200

Squareness between base and fence (A) and fence (B)

0.1/65 (Height of fence (A))

0.1/49 (Height of fence (B))

 

Flatness of fence (A) and fence (B)

0.15

Squareness between dummy disc and fence (A) and fence (B)

0.15/100

Squareness between fence (A) and fence (B) and slide pipes

 

(Place a square against fences (see Fig. 56), slide the head and

0.15/180

check for any clearance between the dummy disc and the square.)

 

Squareness between dummy disc and turn table

0.15/100

Surface alignment of base and turn table

 

(Use the upper surface of the base as a reference.)

(+) 0.1

 

 

(-) 0.2

Fig. 56

 

 

 

-39-

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Models C 8FSE, C 8FSHE Remark Contents Selling Point Descriptions Laser marker Only the Model C 8FSHEPositive angle stoppers Slide cutting Miter cutting Compound miter and bevel cutting Specifications Specifications· 216 mm 8-1/2 TCT saw blade 15.9 mm 5/8 bore, NT24 Specification comparisons Comparisons with Similar ProductsFor Europe and others Except for the U.S.A and Canada C8FSE/C8FSHE For the U.S.A and Canada 8FB2 Right angleFull-load current a 9.2 a Precautions in Sales Promotion Safety instructionsPage Relative standards Laser marker only the Model C 8FSHEPrecautions concerning brake Ambient illuminance and visibility of laser lineAdjustment and Operational Precautions Confirmation for use of sub fence Optional accessoryConfirmation of saw blade lower limit position Position adjustment of laser line Only the Model C 8FSHE How to use the vise assembly Adjustment of table insert positionCutting operation Page Bevel scale Clamp lever Tighten Crown molding stopper R Page Adjustment of Components Bevel angle adjustmentBall bushing Linear bearing Packing Precautions in disassembly and reassembly Repair GuideTurn table and base assy Page Lower guard, link, spindle assy and dust guide Then remove the Lower Guard 215 from the Bearing HolderPage Armature assy and lock lever Page Laser marker Vise ass’yReassembly Special attentionWiring diagram Page Page Page Reassembly requiring adjustment Checking of insulation distanceNo-load current Lubrication Product precisionAdjustment of laser marker accuracy Page Page Troubleshooting guide 211Bushing 115 and slide Page 160 107 Standard Repair Time Unit Schedules 8FSHE8FSE Slide Compound SAW 8FSHE 501 Parts SUB Fence For USA, can Nylon Clip Ball Bearing 608VVC2PS2L Standard Accessories Model C 8FSE 8FSE 162 153 152 8FSE Scale a For USA, can Carbon Brush 1 Pair For GBR 110V, USA, CAN, VEN, TPE Lock Lever Spring Includ 626
Top Page Image Contents