Hitachi C 8FSHE, C 8FSE specifications Adjustment of laser marker accuracy

Page 43

8. Adjustment of laser marker accuracy

(1)Construction of laser marker and functions of each component

The Adjuster [88] located at the side of Hinge (A) Ass’y [87] is a screw used for moving the Laser Marker [107] horizontally. The laser line can be aligned with the left side of the cutting width (saw blade) or the ink line on the right side by means of the Adjuster [88]. The accuracy of the Laser Marker [107] is adjusted by the two Seal Lock Hex. Socket Set Screws M5 x 6 [103].

The Seal Lock Hex. Socket Set Screw M5 x 6 [103] located at the front is mainly used for adjusting the squareness with the fence surface.

The Seal Lock Hex. Socket Set Screw M5 x 6 [103] located under the Laser Marker [107] is mainly used for adjusting the squareness with the base surface (Fig. 57-a).

The laser line will shift to the right in parallel when the Adjuster [88] is turned clockwise, and shift to the left when turned counterclockwise.

CAUTION: Exercise utmost caution in handling the switch trigger for the position adjustment of the laser line, as the power plug is plugged into the receptacle during operation.

If the switch trigger is pulled inadvertently, the saw blade can rotate and result in unexpected accidents.

Do not stare into beam while the laser marker is lighting. Do not observe beam directly with an optical instrument.

If your eye is exposed directly to the laser beam, it can be hurt.

Instruct the customer not to stare into beam. In addition, instruct the customer not to give strong impact to the laser marker (main body of tool) and not to dismantle the laser marker. Use of controls or adjustments or performance of procedures other than those specified in this TECHNICAL DATA AND SERVICE MANUAL and the Instruction Manual may result in hazardous radiation exposure.

Fig. 57-a

Hinge (A) Ass’y [87]

Fig.55-a

Laser Marker [107]

 

-40-

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Models C 8FSE, C 8FSHE Remark Contents Laser marker Only the Model C 8FSHE Selling Point DescriptionsPositive angle stoppers Slide cutting Miter cutting Compound miter and bevel cutting Specifications Specifications· 216 mm 8-1/2 TCT saw blade 15.9 mm 5/8 bore, NT24 Comparisons with Similar Products Specification comparisonsFor Europe and others Except for the U.S.A and Canada C8FSE/C8FSHE 8FB2 Right angle For the U.S.A and CanadaFull-load current a 9.2 a Safety instructions Precautions in Sales PromotionPage Laser marker only the Model C 8FSHE Relative standardsAmbient illuminance and visibility of laser line Precautions concerning brakeConfirmation for use of sub fence Optional accessory Adjustment and Operational PrecautionsConfirmation of saw blade lower limit position Position adjustment of laser line Only the Model C 8FSHE Adjustment of table insert position How to use the vise assemblyCutting operation Page Bevel scale Clamp lever Tighten Crown molding stopper R Page Bevel angle adjustment Adjustment of ComponentsBall bushing Linear bearing Packing Repair Guide Precautions in disassembly and reassemblyTurn table and base assy Page Then remove the Lower Guard 215 from the Bearing Holder Lower guard, link, spindle assy and dust guidePage Armature assy and lock lever Page Vise ass’y Laser markerSpecial attention ReassemblyWiring diagram Page Page Page Checking of insulation distance Reassembly requiring adjustmentNo-load current Product precision LubricationAdjustment of laser marker accuracy Page Page 211 Troubleshooting guideBushing 115 and slide Page 160 107 8FSHE Standard Repair Time Unit Schedules8FSE Slide Compound SAW 8FSHE 501 Parts SUB Fence For USA, can Nylon Clip Ball Bearing 608VVC2PS2L Standard Accessories Model C 8FSE 8FSE 162 153 152 8FSE Scale a For USA, can Carbon Brush 1 Pair For GBR 110V, USA, CAN, VEN, TPE Lock Lever Spring Includ 626
Top Page Image Contents