Hitachi C 8FSHE, C 8FSE specifications Positive angle stoppers

Page 5
Soft grip handle
The handles are widely covered with soft-touch elastomer (rubber-like soft resin).
It is slip-resistant and securely fits in the palm of a hand even if the gripping hand sweats.
Legible scale
The Models C 8FSE and C 8FSHE have legibly labeled angle scale and bevel scale while the current Model C 8FB2 has the scale printed on the die casting.
-2-
Dust collecting performance (%) =
x 100
*1: This is a method to cut a workpiece by shaking the motor head.
*2: This is a method to cut a workpiece by sliding the motor head from the front. The dust collecting performance is obtained from the following formula:
Weight of sawdust accumulated in the dust bag (g) Weight of all sawdust during cutting (g)
Slide cutting *2
(Size of the workpiece:
30 mm x 150 mm (1-3/16” x 5-29/32”))

Positive angle stoppers

The Models C 8FSE and C 8FSHE have positive angle stoppers in the turn table at the right and the left of the 0° center setting, at 15°, 22.5°, 31.6° and 45° settings. Thanks to the positive angle stoppers, positioning can be done more securely than the ball index method utilized in the current Model C 8FB2. In addition, a lever is provided at the lower tip of the turn table to secure or release the positive angle stoppers.

Adjustment of the turn table and positioning can be easily done while holding the side handle.

Bevel cutting range: Left 48° to right 5°

Possible range of bevel cutting is from left 48 degrees to right 5 degrees. By the simple operation of the set pin, you can set the position of the right angle and left 45 degrees.

In addition, setting to approximately 30 degrees and 33.9 degrees for crown molding cutting can be done by this set pin.

Fig. 3

Fig. 4

Set pin

High dust collecting performance

The dust collecting performance of the Models C 8FSE and C 8FSHE are remarkably higher than the other models thanks to the adoption of new dust guide and gear case.

 

 

 

Table 1

 

 

 

(%)

Cutting

Maker

HITACHI

 

 

 

method

Model

 

C 8FSE

 

C 8FB2

P1 and P2

P3

B

 

 

C 8FSHE

 

 

 

 

 

 

 

 

 

 

 

 

Press cutting *1

 

 

75.0

 

25.0

5.9

31.3

62.2

(Size of the workpiece:

 

 

 

60 mm x 60 mm (2-3/8” x 2-3/8”))

 

 

 

 

 

 

80.0

45.0

11.0

72.3

74.5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Models C 8FSE, C 8FSHE Remark Contents Laser marker Only the Model C 8FSHE Selling Point DescriptionsPositive angle stoppers Slide cutting Miter cutting Compound miter and bevel cutting Specifications Specifications· 216 mm 8-1/2 TCT saw blade 15.9 mm 5/8 bore, NT24 For Europe and others Except for the U.S.A and Canada Specification comparisonsComparisons with Similar Products C8FSE/C8FSHE 8FB2 Right angle For the U.S.A and CanadaFull-load current a 9.2 a Safety instructions Precautions in Sales PromotionPage Laser marker only the Model C 8FSHE Relative standardsAmbient illuminance and visibility of laser line Precautions concerning brakeConfirmation of saw blade lower limit position Adjustment and Operational PrecautionsConfirmation for use of sub fence Optional accessory Position adjustment of laser line Only the Model C 8FSHE Adjustment of table insert position How to use the vise assemblyCutting operation Page Bevel scale Clamp lever Tighten Crown molding stopper R Page Ball bushing Linear bearing Adjustment of ComponentsBevel angle adjustment Packing Turn table and base assy Precautions in disassembly and reassemblyRepair Guide Page Then remove the Lower Guard 215 from the Bearing Holder Lower guard, link, spindle assy and dust guidePage Armature assy and lock lever Page Vise ass’y Laser markerSpecial attention ReassemblyWiring diagram Page Page Page No-load current Reassembly requiring adjustmentChecking of insulation distance Product precision LubricationAdjustment of laser marker accuracy Page Page 211 Troubleshooting guideBushing 115 and slide Page 160 107 8FSHE Standard Repair Time Unit Schedules8FSE Slide Compound SAW 8FSHE 501 Parts SUB Fence For USA, can Nylon Clip Ball Bearing 608VVC2PS2L Standard Accessories Model C 8FSE 8FSE 162 153 152 8FSE Scale a For USA, can Carbon Brush 1 Pair For GBR 110V, USA, CAN, VEN, TPE Lock Lever Spring Includ 626
Top Page Image Contents