Hitachi C 8FSHE, C 8FSE specifications Adjustment and Operational Precautions

Page 19

ADJUSTMENT AND OPERATIONAL PRECAUTIONS

1. Confirmation of saw blade lower limit position

The lower limit of the saw blade cutting depth is factory-adjusted so that when the saw blade is fully lowered, its cutting edge is 10 to 11 mm (13/32" to 7/16") below the upper surface of the turn table in order to cut workpieces completely without cutting the bottom of the turn table groove. Lower the saw blade and check that it stops at the correct position (Fig. 16-a).

When changing the position of the 8 mm depth adjustment bolt that serves as the lower limit position stopper of the saw blade, perform the following steps.

(1)Make the tip of the 8 mm depth adjustment bolt contact with the hinge.

(2)Turn the 8 mm depth adjustment bolt with a 13-mm wrench to adjust the lower limit position of the saw blade (Fig. 16-c).

CAUTION: Perform the adjustment carefully to ensure that the saw blade does not cut into the turn table.

Fig. 16-a

Fig. 16-b

8 mm depth adjustment bolt

Turn table

Fig. 16-c

8 mm depth adjustment bolt

2. Confirmation for use of sub fence (Optional accessory)

The sub fence is optionally available (located at the front right of the base). Use the sub fence for miter cutting and right bevel cutting. The sub fence supports the workpiece widely for stable cutting. In the case of left bevel cutting, raise the sub fence as illustrated in Fig. 17 and turn it counterclockwise.

*For the U.S.A. and Canada, the Models C 8FSHE and C8FSE are equipped with the sub fence as a standard accessory.

Fig. 17

Sub fence

NOTE: Mount the sub fence as follows.

Insert the flat-head screw M6 into fence (B) and mount the sub fence and the plate. Then tighten the nylon nut M6 with the attached 10-mm box wrench so that the sub fence can turn smoothly.

WARNING: In the case of left bevel cutting, turn the sub fence counterclockwise. Otherwise the main body or the saw blade may contact the sub fence resulting in an injury. Be sure to instruct the customers to turn the sub fence counterclockwise in the case of left bevel cutting.

-16-

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Models C 8FSE, C 8FSHE Remark Contents Laser marker Only the Model C 8FSHE Selling Point DescriptionsPositive angle stoppers Slide cutting Miter cutting Compound miter and bevel cutting Specifications Specifications· 216 mm 8-1/2 TCT saw blade 15.9 mm 5/8 bore, NT24 Comparisons with Similar Products Specification comparisonsFor Europe and others Except for the U.S.A and Canada C8FSE/C8FSHE 8FB2 Right angle For the U.S.A and CanadaFull-load current a 9.2 a Safety instructions Precautions in Sales PromotionPage Laser marker only the Model C 8FSHE Relative standardsAmbient illuminance and visibility of laser line Precautions concerning brakeConfirmation for use of sub fence Optional accessory Adjustment and Operational PrecautionsConfirmation of saw blade lower limit position Position adjustment of laser line Only the Model C 8FSHE Adjustment of table insert position How to use the vise assemblyCutting operation Page Bevel scale Clamp lever Tighten Crown molding stopper R Page Bevel angle adjustment Adjustment of ComponentsBall bushing Linear bearing Packing Repair Guide Precautions in disassembly and reassemblyTurn table and base assy Page Then remove the Lower Guard 215 from the Bearing Holder Lower guard, link, spindle assy and dust guidePage Armature assy and lock lever Page Vise ass’y Laser markerSpecial attention ReassemblyWiring diagram Page Page Page Checking of insulation distance Reassembly requiring adjustmentNo-load current Product precision LubricationAdjustment of laser marker accuracy Page Page 211 Troubleshooting guideBushing 115 and slide Page 160 107 8FSHE Standard Repair Time Unit Schedules8FSE Slide Compound SAW 8FSHE 501 Parts SUB Fence For USA, can Nylon Clip Ball Bearing 608VVC2PS2L Standard Accessories Model C 8FSE 8FSE 162 153 152 8FSE Scale a For USA, can Carbon Brush 1 Pair For GBR 110V, USA, CAN, VEN, TPE Lock Lever Spring Includ 626
Top Page Image Contents