Hitachi C 8FSHE, C 8FSE specifications Crown molding stopper R

Page 25

2 Tilt the motor head to the left and set the bevel angle as follows:

*For 45° type crown moldings: 30° ( mark)

*For 38° type crown moldings: 33.9° ( mark)

3 Position the crown molding so that the upper surface ( in Fig. 25) contacts the fence as indicated in Fig. 30.

(2)Setting to cut crown moldings at positions 2 and 3 in Fig. 26 (see Fig. 29; tilt the head to the left):

1 Turn the turn table to the left and set the miter angle as follows:

*For 45° type crown moldings: 35.3° ( mark)

*For 38° type crown moldings: 31.6° ( mark)

2 Tilt the head to the left and set the bevel angle as follows:

*For 45° type crown moldings: 30° ( mark)

*For 38° type crown moldings: 33.9° ( mark)

3 Position the crown molding so that the lower surface ( in Fig. 25) contacts the fence as shown in Fig. 31.

Fig. 28

Fig. 29

Turn table

Fig. 30

Turn table

Fig. 31

Cutting method of crown molding without tilting the saw blade

(1)Crown molding stoppers (L) and (R) (optional accessories) allow easier cuts of crown molding without tilting the saw blade. Mount them to both sides the base as shown

in Fig. 32-a. After mounting, tighten the 6 mm knob bolts to

secure the crown molding stoppers. [Optional accessories used]

•Crown molding vise ass’y (including crown molding stopper (L))

•Crown molding stopper (L)

•Crown molding stopper (R)

(2)The crown molding vise (B) (optional accessory) can be mounted on either the left fence (fence (B)) or the right fence (fence (A)). It can unite with the slope of the crown molding and the vice can be pressed down.

Then turn the upper knob, as necessary, to securely attach the crown molding in position. To raise or lower the vise assembly, first loosen the 6 mm knob bolt.

After adjusting the height, firmly tighten the 6 mm wing bolt; then turn the upper knob, as necessary, to securely attach the crown molding in position. (see Fig. 32-b)

 

Fig. 32-a

 

 

Crown molding stopper (R)

 

 

 

 

 

 

 

Crown molding vise ass’y

 

 

 

(optional accessory)

 

 

(optional accessory)

 

 

 

 

 

 

 

 

6 mm knob

bolt

6 mm knob bolt

Crown molding stopper (L)

6 mm wing bolt (optional accessory)

Fig. 32-b

Crown molding vise ass’y (optional accessory)

6 mm knob bolt

6 mm wing bolt

-22-

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Models C 8FSE, C 8FSHE Remark Contents Laser marker Only the Model C 8FSHE Selling Point DescriptionsPositive angle stoppers Slide cutting Miter cutting Compound miter and bevel cutting Specifications Specifications· 216 mm 8-1/2 TCT saw blade 15.9 mm 5/8 bore, NT24 Comparisons with Similar Products Specification comparisonsFor Europe and others Except for the U.S.A and Canada C8FSE/C8FSHE 8FB2 Right angle For the U.S.A and CanadaFull-load current a 9.2 a Safety instructions Precautions in Sales PromotionPage Laser marker only the Model C 8FSHE Relative standardsAmbient illuminance and visibility of laser line Precautions concerning brakeConfirmation for use of sub fence Optional accessory Adjustment and Operational PrecautionsConfirmation of saw blade lower limit position Position adjustment of laser line Only the Model C 8FSHE Adjustment of table insert position How to use the vise assemblyCutting operation Page Bevel scale Clamp lever Tighten Crown molding stopper R Page Bevel angle adjustment Adjustment of ComponentsBall bushing Linear bearing Packing Repair Guide Precautions in disassembly and reassemblyTurn table and base assy Page Then remove the Lower Guard 215 from the Bearing Holder Lower guard, link, spindle assy and dust guidePage Armature assy and lock lever Page Vise ass’y Laser markerSpecial attention ReassemblyWiring diagram Page Page Page Checking of insulation distance Reassembly requiring adjustmentNo-load current Product precision LubricationAdjustment of laser marker accuracy Page Page 211 Troubleshooting guideBushing 115 and slide Page 160 107 8FSHE Standard Repair Time Unit Schedules8FSE Slide Compound SAW 8FSHE 501 Parts SUB Fence For USA, can Nylon Clip Ball Bearing 608VVC2PS2L Standard Accessories Model C 8FSE 8FSE 162 153 152 8FSE Scale a For USA, can Carbon Brush 1 Pair For GBR 110V, USA, CAN, VEN, TPE Lock Lever Spring Includ 626
Top Page Image Contents