Hitachi C 8FSHE, C 8FSE specifications

Page 23
Fig. 24

NOTE:

Techniques to avoid unwanted cutting marks

Uneven and unwanted cutting marks can be avoided by shifting from 3 press cutting to 4 slide cutting in a single, uninterrupted motion.

Techniques to avoid burnt marks

Burnt marks can be avoided by shifting from 3 press cutting to 4 slide cutting in a single, uninterrupted motion in the same manner as the above, applying a slight lateral force toward the cut-off side. Advise the customer that he or she will quickly develop a "feel" and skill for smooth cutting after performing two or three practice cutting operations.

(5)Miter cutting

Miter cutting is accomplished by turning the turn table. (For details, please refer to the Instruction Manual "Miter cutting procedures.")

(6)Bevel cutting

Bevel cutting of 0 - 45° to the left or 0 - 5° to the right is accomplished by inclining the motor head section. (For details, refer to the Instruction Manual "Bevel cutting procedures.")

WARNING: When the workpiece is secured on the left or right side of the blade, the short cut-off portion will come to rest on the right or left side of the saw blade. Always turn the power off and let the saw blade stop completely before raising the handle from the workpiece. If the handle is raised while the saw blade is still rotating, the cut-off piece may become jammed against the saw blade causing fragments to scatter about dangerously. When stopping the bevel cutting operation halfway, start cutting after pulling back the motor head to the initial position. Starting from halfway, without pulling back, causes the safety cover to be caught in the cutting groove of the workpiece and to contact the saw blade.

CAUTION: When cutting a workpiece of 50 mm (1-15/16”) height in the left 45° bevel cutting position or a workpiece of 70 mm (2-3/4”) height in the right 5° bevel cutting position, adjust the lower limit position of the motor head so that the gap between the lower edge of the motor head and the workpiece will be 2 to 3 mm (5/64" to 1/8") at the lower limit position (refer to the Instruction Manual "Checking the saw blade lower limit position").

(7)Compound (miter + bevel) cutting

Compound (miter + bevel) cutting can be accomplished by combining the miter cutting and bevel cutting operations described in paragraphs (5) and (6) above. (For details, refer to the Instruction Manual "Compound cutting procedures.") When the saw blade is inclined 45° to the left, the turn table can be turned up to 45° to the left and right.

(8)Cut surface quality during miter/bevel cutting

The quality of the cut surface depends on the type of cutting operation (miter or bevel), the type and sharpness of the saw blade, whether the workpiece is cut to the left or right, and various other factors. In miter and bevel cutting in particular, cutting is performed across the wood grain, so the condition of the cut surface depends on whether the wood is cut with or against the grain. This is the same as when using electric portable planers. Customers should be advised of these phenomena so that they understand that in cases when the cut surface may not be as smooth as expected or hoped for, it is not caused by the performance of the saw blade or the Models C 8FSE/C 8FSHE.

In the cutting examples illustrated in Fig. 24, the cut surfaces on the sides marked ( A ) (cut with the

-20-

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Models C 8FSE, C 8FSHE Remark Contents Laser marker Only the Model C 8FSHE Selling Point DescriptionsPositive angle stoppers Slide cutting Miter cutting Compound miter and bevel cutting Specifications Specifications· 216 mm 8-1/2 TCT saw blade 15.9 mm 5/8 bore, NT24 For Europe and others Except for the U.S.A and Canada Specification comparisonsComparisons with Similar Products C8FSE/C8FSHE 8FB2 Right angle For the U.S.A and CanadaFull-load current a 9.2 a Safety instructions Precautions in Sales PromotionPage Laser marker only the Model C 8FSHE Relative standardsAmbient illuminance and visibility of laser line Precautions concerning brakeConfirmation of saw blade lower limit position Adjustment and Operational PrecautionsConfirmation for use of sub fence Optional accessory Position adjustment of laser line Only the Model C 8FSHE Adjustment of table insert position How to use the vise assemblyCutting operation Page Bevel scale Clamp lever Tighten Crown molding stopper R Page Ball bushing Linear bearing Adjustment of ComponentsBevel angle adjustment Packing Turn table and base assy Precautions in disassembly and reassemblyRepair Guide Page Then remove the Lower Guard 215 from the Bearing Holder Lower guard, link, spindle assy and dust guidePage Armature assy and lock lever Page Vise ass’y Laser markerSpecial attention ReassemblyWiring diagram Page Page Page No-load current Reassembly requiring adjustmentChecking of insulation distance Product precision LubricationAdjustment of laser marker accuracy Page Page 211 Troubleshooting guideBushing 115 and slide Page 160 107 8FSHE Standard Repair Time Unit Schedules8FSE Slide Compound SAW 8FSHE 501 Parts SUB Fence For USA, can Nylon Clip Ball Bearing 608VVC2PS2L Standard Accessories Model C 8FSE 8FSE 162 153 152 8FSE Scale a For USA, can Carbon Brush 1 Pair For GBR 110V, USA, CAN, VEN, TPE Lock Lever Spring Includ 626
Top Page Image Contents