Hitachi C 8FSHE, C 8FSE specifications Lower guard, link, spindle assy and dust guide

Page 31

2. Lower guard, link, spindle ass'y and dust guide

(1)Remove the Bolt (W/Washers) M6 x 16 (Black) [207] and the Machine Screws (W/Washers) M5 x 8

[191]with the Box Wrench 10 mm [501]. Remove the Spindle Cover [192] from the Gear Case [198].

(2)Remove the Bolt (Left Hand) W/Washer M7 x 17.5 [210] with the Box Wrench 10 mm [501]. Remove Washer (D) [221], TCT Saw Blade [211] and Washer (D) [221] in this order from the Spindle Ass’y

(3)Remove the two Flat Hd. Screws M4 x 10 [213]. Remove the Cover [214] and the Lower Guard [215] from the Bearing Holder [219].

NOTE: Be sure to release the hook of the Return Spring [216] from the groove of the Lower Guard

[215]then remove the Lower Guard [215] from the Bearing Holder [219].

(4)Remove the Machine Screw M5 x 12 [89] then remove the Spacer [90] and the Link [91] from Hinge (A) Ass’y [87].

(5)Remove the two Machine Screws M5 x 20 [222] and then remove the Spindle Ass'y [217] by gently hammering the Gear Case [198] with a plastic hammer.

(6)Remove the Machine Screws (W/Washers) M4 x 12 (Black) [194] and then remove the Dust Guide

[208]and the Guide Holder [209].

Fig. 40

3. Spring, support, hinge ass'y, ball bushing, bushing, holder (A) and gear case

(1)Remove the Machine Screw (W/Washers) M4 x 12 (Black) [111] to remove the Nylon Clip [112]. Remove the Machine Screw (W/Washers) M4 x 12 (Black) [195] and remove the Nylon Clip [196] from the Gear Case [198] (head).

(2)Push out the Cord Bush [154] from the inside of the Housing Ass’y [155]. Disconnect the connector of the Switching Power Supply Ass’y [165] and the Laser Marker [107]. Open the Cord Bush [154] to remove it from the cord of the Laser Marker [107].

(3)Remove the Seal Lock Hex. Socket Hd. Bolt M5 x 10 [197].

NOTE: The Seal Lock Hex. Socket Hd. Bolt M5 x 10 [197] acts as the upper limit stopper of the Gear Case [198] (head). Be careful that the Gear Case [198] (head) is raised by the force of the Spring [85] when the Seal Lock Hex. Socket Hd. Bolt M5 x 10 [197] is removed.

(4) Remove the Hex. Socket Set Screw M6 x 8 [121]. Make a flat-blade screwdriver contact with the end surface of Hinge Shaft (A) [92] and lightly tap the screwdriver with a plastic hammer to remove Hinge Shaft (A) [92].

NOTE: Be sure to hold the Gear Case [198] (head) with hand during disassembly to prevent the Gear Case [198] (head) from being dropped when removing Hinge Shaft (A) [92] from the hole of the Gear Case [198] (head). Then the Spring [85] and the Sleeve [84] can be removed from the Gear Case [198] (head).

(5)Remove the two Hex. Socket Set Screws M8 x 10 [86]. Then gently hammer the Support [113] outward and remove it from slide pipes (A) and (B).

-28-

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Models C 8FSE, C 8FSHE Remark Contents Laser marker Only the Model C 8FSHE Selling Point DescriptionsPositive angle stoppers Slide cutting Miter cutting Compound miter and bevel cutting Specifications Specifications· 216 mm 8-1/2 TCT saw blade 15.9 mm 5/8 bore, NT24 Comparisons with Similar Products Specification comparisonsFor Europe and others Except for the U.S.A and Canada C8FSE/C8FSHE 8FB2 Right angle For the U.S.A and CanadaFull-load current a 9.2 a Safety instructions Precautions in Sales PromotionPage Laser marker only the Model C 8FSHE Relative standardsAmbient illuminance and visibility of laser line Precautions concerning brakeConfirmation for use of sub fence Optional accessory Adjustment and Operational PrecautionsConfirmation of saw blade lower limit position Position adjustment of laser line Only the Model C 8FSHE Adjustment of table insert position How to use the vise assemblyCutting operation Page Bevel scale Clamp lever Tighten Crown molding stopper R Page Bevel angle adjustment Adjustment of ComponentsBall bushing Linear bearing Packing Repair Guide Precautions in disassembly and reassemblyTurn table and base assy Page Then remove the Lower Guard 215 from the Bearing Holder Lower guard, link, spindle assy and dust guidePage Armature assy and lock lever Page Vise ass’y Laser markerSpecial attention ReassemblyWiring diagram Page Page Page Checking of insulation distance Reassembly requiring adjustmentNo-load current Product precision LubricationAdjustment of laser marker accuracy Page Page 211 Troubleshooting guideBushing 115 and slide Page 160 107 8FSHE Standard Repair Time Unit Schedules8FSE Slide Compound SAW 8FSHE 501 Parts SUB Fence For USA, can Nylon Clip Ball Bearing 608VVC2PS2L Standard Accessories Model C 8FSE 8FSE 162 153 152 8FSE Scale a For USA, can Carbon Brush 1 Pair For GBR 110V, USA, CAN, VEN, TPE Lock Lever Spring Includ 626
Top Page Image Contents