Hitachi C 8FSE, C 8FSHE specifications

Page 34

5. Handle cover, switch, light, cord, stator ass'y and housing ass'y

(1)Remove the motor section according to the above step 4-(1)(2).

(2)Remove the seven Tapping Screws (W/Flange) D4 x 20 (Black) [163] and remove the Handle Cover [164].

(3)Disconnect the connectors of the Switching Power Supply Ass’y [165] and Light (H) Ass’y [175] and remove Light (H) Ass’y [175].

(4)Turn Cap (A) [174] and remove it, then you can remove the Clear Cover [173].

(5)(For the U.S.A. and Canada)

Cut off the two Connectors [168] that are crimped onto the internal wires coming from the Stator Ass'y

[181]and the Switch (3P Faston Type) W/O Lock [170]. (Except for the U.S.A. and Canada)

Loosen the screw of Pillar Terminal(A) [171] with a flatblade screwdriver and disconnect the internal wires.

(6)Removal of the Switch (3P Faston Type) W/O Lock [170]:

(a)Remove the Handle Cover [164] from the Housing Ass'y [155] according to the above step 5-(1)(2). Then the Switch (3P Faston Type) W/O Lock [170] can be removed.

(b)The Stator Ass’y [181] and Internal Wire (G) [169] are provided with a claw to prevent coming off of the connector. When removing the Stator Ass’y [181] and Internal Wire (G) [169] from the Switch (3P Faston Type) W/O Lock [170], pull out the Stator Ass’y [181] and Internal Wire (G) [169] while pressing the claw.

(7)Disconnect the faston of the Switching Power Supply Ass’y [165] from the two Switches (W/Cover)

[167]for the Laser Marker [107] and Light (H) Ass’y [175]. Push the Switch (W/Cover) [167] from the inside of the Housing Ass’y [155] and remove the Switch (W/Cover) [167].

(8)Remove the Tapping Screw (W/Flange) D4 x 16 [151] and remove the Switching Power Supply Ass’y

[165]from the Housing Ass’y [155].

(9)Removal of the Stator Ass’y [181]:

(a)Remove the Fan Guide [178] from the Housing Ass’y [155].

(b)Remove the two Hex. Hd. Tapping Screws D4 x 60 [179] that secure the Stator Ass’y [181] to the Housing Ass’y [155]. Remove the two Brush Terminals [180] from the Brush Holder [159].

(c)Pull out the Stator Ass’y [181] by lightly tapping the Housing Ass’y [155] at the surface where the Gear Case [198] is mounted with a plastic hammer.

(10)Remove the two Tapping Screw (W/Flange) D4 x 16 [151] and remove the Cord [110] and the Cord Armor D10.1 [152].

Fig. 43

-31-

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Models C 8FSE, C 8FSHE Remark Contents Selling Point Descriptions Laser marker Only the Model C 8FSHEPositive angle stoppers Slide cutting Miter cutting Compound miter and bevel cutting Specifications Specifications· 216 mm 8-1/2 TCT saw blade 15.9 mm 5/8 bore, NT24 Comparisons with Similar Products Specification comparisonsFor Europe and others Except for the U.S.A and Canada C8FSE/C8FSHE For the U.S.A and Canada 8FB2 Right angleFull-load current a 9.2 a Precautions in Sales Promotion Safety instructionsPage Relative standards Laser marker only the Model C 8FSHEPrecautions concerning brake Ambient illuminance and visibility of laser lineConfirmation for use of sub fence Optional accessory Adjustment and Operational PrecautionsConfirmation of saw blade lower limit position Position adjustment of laser line Only the Model C 8FSHE How to use the vise assembly Adjustment of table insert positionCutting operation Page Bevel scale Clamp lever Tighten Crown molding stopper R Page Bevel angle adjustment Adjustment of ComponentsBall bushing Linear bearing Packing Repair Guide Precautions in disassembly and reassemblyTurn table and base assy Page Lower guard, link, spindle assy and dust guide Then remove the Lower Guard 215 from the Bearing HolderPage Armature assy and lock lever Page Laser marker Vise ass’yReassembly Special attentionWiring diagram Page Page Page Checking of insulation distance Reassembly requiring adjustmentNo-load current Lubrication Product precisionAdjustment of laser marker accuracy Page Page Troubleshooting guide 211Bushing 115 and slide Page 160 107 Standard Repair Time Unit Schedules 8FSHE8FSE Slide Compound SAW 8FSHE 501 Parts SUB Fence For USA, can Nylon Clip Ball Bearing 608VVC2PS2L Standard Accessories Model C 8FSE 8FSE 162 153 152 8FSE Scale a For USA, can Carbon Brush 1 Pair For GBR 110V, USA, CAN, VEN, TPE Lock Lever Spring Includ 626
Top Page Image Contents