American Standard UV05 manual UVC configuration parameters OM

UVC Configuration Parameters

UVC Configuration Parameters

The UVC is been provided with a number of configuration variables as listed in the following table. These configuration variables are stored in UVC non-volatile memory. For a description of supported network variables for each protocol, refer to Protocol Data Packet bulletin ED 15065.

Table 26: UVC configuration parameters (OM 751)

Configuration Parameter Name	Abr.	Notes	Default	LUI Menu
				Item1
Occupied Cooling Setpoint	OCS		73°F (23°C)	Co
Standby Cooling Setpoint	SCS		77°F (25°C)	C5
Unoccupied Cooling Setpoint	UCS		82°F (28°C)	CU
Occupied Heating Setpoint	OHS		70°F (21°C)	Ho
Standby Heating Setpoint	SHS		66°F (19°C)	H5
Unoccupied Heating Setpoint	UHS		61°F (16°C)	HU
Local Bypass Time		Tenant override	120 min
Space CO2 Setpoint2	CO S		1200 PPM
	2
Space Humidity Setpoint2	RHS	used with both active (reheat) and passive dehumidification	60% Rh
		sequences
Emergency Heat Enable		0 = disable, 1 = enable (uses auxiliary heat where primary heat is	1	H1
		not applicable)
Emergency Heat Setpoint	EHS		54°F (12°C)	H2
Emergency Heat Shutdown		0 = no emergency heat during shutdown, 1 = emergency heat	0	H3
Configuration		available during shutdown
Wall Sensor Type2		0 = +/- 3°F, 1 = 55°F to 85°F	0	r5
Slave Type Configuration2		0 = independent slave, 1 = dependent slave	0	SL
OAD Min Position High-Speed Setpoint	OADH	(this variable will be factory set to 5% open when the unit is ordered	20% open	o2
		with optional CO2 DCV)
OAD Min Position Med-Speed Setpoint	OADM	(this variable is ignored when the unit is ordered with optional CO2	25% open	o3
		DCV)
OAD Min Position Low-Speed Setpoint	OADL	(this variable is ignored when the unit is ordered with optional CO2	30% open	o4
		DCV)
Exhaust Interlock OAD Min Position	EOAD	OA damper minimum position when the exhaust interlock input is	99% open	o5
Setpoint		energized
Energize Exhaust Fan OAD Setpoint	OADE	defines position above which exhaust fan output will be energized	12% open	o6
OAD Max Position Setpoint	OAMX		99% open	o7
OAD Lockout Enable		0 = disable, 1 = enable (this variable will be factory set to 1 when	0	o8
		the unit is ordered as a recirc unit with no OAD)
OAD Lockout Setpoint		OA temperature below which the OA damper will remain closed		o9
	OALS	(this variable will be factory set to –99°C when the unit is ordered	36°F (2°C)
		as a recirc unit with no OAD)
Economizer Enable		0 = disable, 1 = enable	1	E1
Economizer OA Temp Setpoint	ETS		68°F (20°C)	E2
Economizer IA/OA Temp Differential	ETD		2°F (1°C)	e3
Economizer OA Enthalpy Setpoint	EES		25 btu/lb (58 kJ/kg)	e5
Economizer IA/OA Enthalpy Differential	EED		1.3 btu/lb (3 kJ/kg)	e6
External BI-3 Configuration		0 = Ventilation Lockout, 1 = Exhaust Interlock	0	B3
External BO-3 Configuration		0 = Exhaust Fan On/Off, 1 = Auxiliary Heat	0	B6
Filter Alarm Enable		0 = disable, 1 = enable	0	CE
Filter Change Hours Setpoint		fan run hours between filter change alarms	700 hrs

McQuay OM 751 47