Powerware 685, 1085 installation manual Removing Front and Rear Supports

Page 14

LEFT HAND

 

 

 

DOOR

 

 

FOAM

(Step 1)

 

SIDE

FRONT

CUSHION

2

SUPPORT

 

SUPPORT

 

 

 

 

1

 

 

 

FLOOR PROTECTOR

(Step 2)

2

2

 

2

 

 

 

1

 

 

 

JACKING

 

1

 

BOLT

 

2

(Step 2)

 

(Step 3)

(Step 8)

 

Figure 5. Removing Front and Rear Supports

3. Loosen, but do not remove, the hardware holding the foam cushions to the front and rear supports (labeled “1” in Figure 5).

WARNING: SERIOUS INJURY MAY OCCUR!

BATTERY CABINETS ARE EXTREMELY HEAVY. IF UNLOADING INSTRUCTIONS

ARE NOT CLOSELY FOLLOWED, CABINET MAY TIP.

4. Turn each jacking bolt consecutively, two full turns, until the foam cushions clear the floor by approximately 3 mm (1/8 in.).

DANGER: RISK OF INSTABILITY!

TURNING THE JACKING BOLTS UNEVENLY MAY CAUSE THE CABINET TO BECOME UNBALANCED. TO PREVENT TIPPING THE CABINET, RAISE AND LOWER THE JACKING BOLTS EVENLY.

DANGER: CABINET MAY TIP!

THE BATTERY CABINET SHOULD ONLY BE RAISED APPROXIMATELY 3 mm (1/8 in.) ABOVE THE FLOOR (JUST ENOUGH TO ALLOW REMOVAL OF THE FOAM CUSHIONS).

5. After the foam cushions clear the floor, remove the hardware loosened in Step 3. Pull the foam cushions out from under the battery cabinet. Please discard or recycle them in a responsible manner.

8

Powerware 9350 Series 685 and 1085 Auxiliary Battery Cabinets

 

 

Installation Manual 164201408 Rev. P00 053002

Image 14
Contents Series 685 Auxiliary Battery Cabinets Important Safety Instructions General Notes About Installing Battery Cabinets Conventions Used in This Manual Table of Contents Typical Battery Cabinets Typical Battery Cabinets IntroductionIdentification of Your Battery System UPSBattery Cabinets For More Information Getting HelpPreparing Your Site Unpacking Your Battery CabinetPreparing for Wiring the Battery Cabinet Environmental ConsiderationsInspecting and Unpacking Each Cabinet Outer Packaging PLY---FOAM CushionsUnloading the Battery Cabinet from the Pallet Removing Front and Rear Supports Creating an Installation Plan Page Connecting to Powerware 9350 30 Powerware 9350 UPS with Integral Battery CabinetsInstallation Manual 164201408 Rev. P00 See for Series TOP View Front View Attaching UPS Base to Series 685 Base Installation Manual 164201408 Rev. P00 Series 685 Battery Cabinet Wiring Detail Series 685 Cabinet Series 1085 Battery Cabinet Wiring Detail Powerware 9350 UPS with Separately Located Battery Cabinets UPS with Separately Located Battery CabinetsSeparate Installation of Series 685 Battery Cabinets Connecting Two Series 685 Bases Separate Installation of Series 1085 Battery Cabinets Connecting Two Series 1085 Bases To Electrically Connect Separate Battery Cabinets to the UPS Installation Manual 164201408 Rev. P00 Completing the Installation Checklist Installation Checklist for Powerware 9350 30 throughThis Page Intentionally Left Blank Connecting to Powerware 9350 ---80 Battery Connections for a PowerwarePowerware 9350---80 or 160 with Separate Battery Cabinets Completing the Installation Checklist Installation Checklist for Powerware Installing a Remote Battery Disconnect Remote Battery Disconnect Enclosure31.1 N-M 255---275 lb-in Table A. Remote Battery Disconnect Power Terminations Table C. Remote Battery Disconnect Circuit Breaker Ratings Series 685 / 1085 Configurations Appendix a --- Customer InformationIntegral Tool Size Torque Battery Cabinet UPS Cabinet 375 200 Type Series 685 Battery Cabinet TOP View Series 1085 Battery Cabinet Series 1085 Battery Cabinet plan TB1 164201408--4 This Page Intentionally Left Blank