Multiquip HTXD6i / STXD6i manual HTX6Di/STX6Di Trowel, Table of Contents

Page 2

TABLE OF CONTENTS

HTX6Di/STX6Di Trowel
Machine Information And Maintenance Log	3
Safety Information	4-9
Tools Needed	10
Machine Information	11
Model	11
Serial Number	11
Program ID	11
General Procedures	12
Setup Jumper Installation	12
Remove Setup Jumper (If Installed)	12
Initial Check And Adjustments	13-14
Preliminary Charge Pressure Adjustment	13
Oil And Coolant Check	13
Hydraulic Oil Check	13
Engine Oil	13
Engine Coolant	14
Service Tool Setup And Connection	15-16
Whiteman Service Tool (WST) Installation	15
Laptop Configuration	17
Connection Procedure	17
Machine Setup And Calibration	18-27
Calibrate Foot Pedal	18
Calibration	19

Secondary Hydraulic Fill Procedures	19
Machine Pressure Adjustment	20
Charge Pressure Adjustment	20
Pitch Pressure Check	20
Pitch Pressure Adjustment	21
Steering Pressure Adjustment	21
Trowel Speed Adjustment\Setup	22
Adjust Zero Stroke Position	22
Left Side Trowel Speed Adjustment	22
Right Side Trowel Speed Adjustment	23
Calibrate Stroke Sensor	23
Pitch Setup	24
Flatten Blades	24
Measure Blade Leading Edge Height	25
Leading Edge Height Adjustment	25
Set Zero Pitch Cylinder Stops	26
Pitch Sensor Calibration	26
Inspection	28-29
Fluid Levels	28
Mechanical	28
Static Blade Pitch Drift Test	29
Fuse Information	30

PAGE 2 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #1 (01/24/14)

Image 2

Contents Model HTXD6i/STXD6i This Manual Must Accompany the Equipment AT ALL TimesTable of Contents HTX6Di/STX6Di TrowelMachine Information and Maintenance LOG Safety Information Safety MessagesGeneral Safety „ALWAYS know the location of the nearestOrder Form PT-160 Trowel SafetyEngine Safety Before servicing equipment„ Never tamper with the factory settings Fuel SafetyBattery Safety „ Use well-insulated gloves when picking up the batteryLifting Transporting SafetyTowing Safety „ Always shutdown engine before transportingEnvironmental Safety Tools Needed Serial Number Machine InformationModel Remove Setup Jumper If installed General ProceduresSetup Jumper Installation Hydraulic Oil Check Initial Check and AdjustmentsOIL and Coolant Check Loosen 1-1/16 jam nut on charge relief valve Item A, FigureEnsure engine is level Engine OilEngine Coolant Service Tool Setup and Connection Click Cancel again when the new screen comes upInput the license key obtained from Multiquip and click OK WST Tool BarClick Finish on the next screen to complete installation Laptop ConfigurationConnection Procedure Necessary to crank or turn on the engineCalibrate Foot Pedal Machine Setup and CalibrationSensor Adjustment Click Calibration button in Pedal Sensor frame FigurePress Start button to begin calibration and follow prompts Secondary Hydraulic Fill ProceduresCalibration Pitch Pressure Check Machine Pressure AdjustmentCharge Pressure Adjustment Restart machineReturn engine rpm to idle Turn off machine and remove gauge Pitch Pressure AdjustmentSteering Pressure Adjustment Left Side Trowel Speed Adjustment Trowel Speed ADJUSTMENT\SETUPAdjust Zero Stroke Position Lower trowel and shut off Loosen Jamb nut Item D, FigureCalibrate Stroke Sensor Right Side Trowel Speed AdjustmentRemove setup jumper or re-enable stroke follower Pitch Setup Flatten BladesLeading Edge Height Adjustment Measure Blade Leading Edge HeightSet Zero Pitch Cylinder Stops Pitch Sensor CalibrationGauge Turn machine off for 10 secondsMechanical InspectionFluid Levels Switch smart pitch switch to off position Static Blade Pitch Drift TestFuse Information Refer to for location on fuse panelPage HERE’S HOW to GET Help