Multiquip HTXD6i / STXD6i manual Inspection, Fluid Levels, Mechanical

Page 28

INSPECTION

FLUID LEVELS

Record the following fluid levels on Machine Information and Maintenance Log in Inspection section. Refer to Fluid Fill and Check section for procedure.

Engine Oil

Engine Coolant Hydraulic Oil

MECHANICAL

1.Grease Points — Ensure that the following Grease Points are greased, wiped down and capped:

•Thrust Collar

•Fingers

2.Stabilizer Rings

a.Verify at least 1 thread is visible below lower bolt on all heim joints (Figure 43).

Figure 43. Visible Thread

b.Verify heim joint is centered, and not rotated, when bolted on Figure 44).

Figure 44. Heim Joint Orientation

3.Hydraulics

•Spot check paint marks on fittings.

•Ensure that there are no leaks.

4.Retardant Spray System

•Fill with water and perform operational check.

•Verify no leaks.

5.Electrical (Cooling Fan)

•Verify fan cycles on when key is turned on (will remain on for 10s).

•Verify air flow direction is outward.

6.Lights

•Verify operation of all 6 machine lights.

7.Switches

•Verify proper operation of all switches.

8.Indicators

•Verify illumination when key is turned on (will remain on for 10s)

•Red Stop Lamp

•Amber Warning Lamp

•Pitch Mode Light

•Cruise Control Light

•Coolant Temp

•Aux 1

•Aux 2

9.Aesthetics

•Paint Quality

-No bare spots

-No scratches

•Decals

-Readable

-Not torn or scratched

PAGE 28 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #1 (01/24/14)

Image 28

Contents Model HTXD6i/STXD6i This Manual Must Accompany the Equipment AT ALL TimesTable of Contents HTX6Di/STX6Di TrowelMachine Information and Maintenance LOG Safety Information Safety MessagesGeneral Safety „ALWAYS know the location of the nearestTrowel Safety Engine SafetyOrder Form PT-160 Before servicing equipmentFuel Safety Battery Safety„ Never tamper with the factory settings „ Use well-insulated gloves when picking up the batteryTransporting Safety Towing SafetyLifting „ Always shutdown engine before transportingEnvironmental Safety Tools Needed Model Machine InformationSerial Number Setup Jumper Installation General ProceduresRemove Setup Jumper If installed Initial Check and Adjustments OIL and Coolant CheckHydraulic Oil Check Loosen 1-1/16 jam nut on charge relief valve Item A, FigureEngine Coolant Engine OilEnsure engine is level Service Tool Setup and Connection Click Cancel again when the new screen comes upInput the license key obtained from Multiquip and click OK WST Tool BarLaptop Configuration Connection ProcedureClick Finish on the next screen to complete installation Necessary to crank or turn on the engineMachine Setup and Calibration Sensor AdjustmentCalibrate Foot Pedal Click Calibration button in Pedal Sensor frame FigureCalibration Secondary Hydraulic Fill ProceduresPress Start button to begin calibration and follow prompts Machine Pressure Adjustment Charge Pressure AdjustmentPitch Pressure Check Restart machineSteering Pressure Adjustment Pitch Pressure AdjustmentReturn engine rpm to idle Turn off machine and remove gauge Trowel Speed ADJUSTMENT\SETUP Adjust Zero Stroke PositionLeft Side Trowel Speed Adjustment Lower trowel and shut off Loosen Jamb nut Item D, FigureRemove setup jumper or re-enable stroke follower Right Side Trowel Speed AdjustmentCalibrate Stroke Sensor Pitch Setup Flatten BladesLeading Edge Height Adjustment Measure Blade Leading Edge HeightSet Zero Pitch Cylinder Stops Pitch Sensor CalibrationGauge Turn machine off for 10 secondsFluid Levels InspectionMechanical Switch smart pitch switch to off position Static Blade Pitch Drift TestFuse Information Refer to for location on fuse panelPage HERE’S HOW to GET Help