Multiquip HTXD6i / STXD6i manual General Safety, „ALWAYS know the location of the nearest

Page 5

SAFETY INFORMATION

GENERAL SAFETY

CAUTION

„NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations.

„Avoid wearing jewelry or loose fi tting clothes that may snag on the controls or moving parts as this can cause serious injury.

„NEVER operate this equipment when not feeling well due to fatigue, illness or when under medication.

„NEVER operate this equipment under the infl uence of drugs or alcohol.

„ALWAYS clear the work area of any debris, tools, etc. that would constitute a hazard while the equipment is in operation.

„No one other than the operator is to be in the working area when the equipment is in operation.

„DO NOT use the equipment for any purpose other than its intended purposes or applications.

NOTICE

„This equipment should only be operated by trained and qualifi ed personnel 18 years of age and older.

„Whenever necessary, replace nameplate, operation and safety decals when they become diffi cult read.

„Manufacturer does not assume responsibility for any accident due to equipment modifi cations. Unauthorized equipment modifi cation will void all warranties.

„NEVER use accessories or attachments that are not recommended by Multiquip for this equipment. Damage to the equipment and/or injury to user may result.

„ALWAYS know the location of the nearest

fire extinguisher.

„ALWAYS know the location of the nearest

first aid kit.

„ALWAYS know the location of the nearest phone or keep a phone on the job site. Also, know the phone numbers of the nearest ambulance, doctor and fire department. This information will be invaluable in the case of an emergency.

HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #1 (01/24/14) — PAGE 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents This Manual Must Accompany the Equipment AT ALL Times Model HTXD6i/STXD6iHTX6Di/STX6Di Trowel Table of ContentsMachine Information and Maintenance LOG Safety Messages Safety Information„ALWAYS know the location of the nearest General SafetyEngine Safety Trowel SafetyOrder Form PT-160 Before servicing equipmentBattery Safety Fuel Safety„ Never tamper with the factory settings „ Use well-insulated gloves when picking up the batteryTowing Safety Transporting SafetyLifting „ Always shutdown engine before transportingEnvironmental Safety Tools Needed Serial Number Machine InformationModel Remove Setup Jumper If installed General ProceduresSetup Jumper Installation OIL and Coolant Check Initial Check and AdjustmentsHydraulic Oil Check Loosen 1-1/16 jam nut on charge relief valve Item A, FigureEnsure engine is level Engine OilEngine Coolant Click Cancel again when the new screen comes up Service Tool Setup and ConnectionWST Tool Bar Input the license key obtained from Multiquip and click OKConnection Procedure Laptop ConfigurationClick Finish on the next screen to complete installation Necessary to crank or turn on the engineSensor Adjustment Machine Setup and CalibrationCalibrate Foot Pedal Click Calibration button in Pedal Sensor frame FigurePress Start button to begin calibration and follow prompts Secondary Hydraulic Fill ProceduresCalibration Charge Pressure Adjustment Machine Pressure AdjustmentPitch Pressure Check Restart machineReturn engine rpm to idle Turn off machine and remove gauge Pitch Pressure AdjustmentSteering Pressure Adjustment Adjust Zero Stroke Position Trowel Speed ADJUSTMENT\SETUPLeft Side Trowel Speed Adjustment Lower trowel and shut off Loosen Jamb nut Item D, FigureCalibrate Stroke Sensor Right Side Trowel Speed AdjustmentRemove setup jumper or re-enable stroke follower Flatten Blades Pitch SetupMeasure Blade Leading Edge Height Leading Edge Height AdjustmentPitch Sensor Calibration Set Zero Pitch Cylinder StopsTurn machine off for 10 seconds GaugeMechanical InspectionFluid Levels Static Blade Pitch Drift Test Switch smart pitch switch to off positionRefer to for location on fuse panel Fuse InformationPage HERE’S HOW to GET Help
Top Page Image Contents