Multiquip HTXD6i / STXD6i manual Gauge, Turn machine off for 10 seconds

Page 27

MACHINE SETUP AND CALIBRATION

b.Install 3.25” Gauge (P/N 32044) over both Left and Right Cylinders as shown in Figure 41.

3.25” GAUGE

Figure 41. Gauge Installation

c.Press Hard Ret. button to retract cylinder onto gauge.

d.Verify gauge is tight between cylinder body and clevis.

e.Press “Set T1” button (Figure 42).

Figure 42. Start Pitch Sensor Calibration

g.Press Hard Ext. Button to fully extend pitch cylinders.

h.Remove gauge.

6.Set Calibration Point 2.

a.Install 2.25” Gauge P/N 32000 over both Left and Right Cylinders as shown in Figure 41.

b.Press Hard Ret. Button to retract cylinder onto gauge.

c.Verify gauge is tight between cylinder body and clevis.

d.Press “Set T2” Button.

e.Record values on Machine Information and Maintenance Log in Machine Setup section.

f.Press Hard Ext. Button to fully extend pitch cylinders.

g.Remove gauge.

7.Set Calibration Point 3.

a.Ensure Hard Ext. is active and pitch cylinders are fully extended.

b.Press “Set L1” button.

c.Record values on Machine Information and Maintenance Log in Machine Setup section.

8.Set Calibration Point 4.

a.Press Hard Ret. button to fully retract cylinders, ensure yoke is against zero pitch stop.

b.Press Soft Ext. button, and wait until yoke is pressing against thrust collar.

c.Press “Set L2” button.

d.Record values on Machine Information and Maintenance Log in Machine Setup section.

9.Once calibrated, move pitch thru range ensuring calibrated signal moves from 0 to 100%.

10.Turn machine off for 10 seconds.

f.Record values on Machine Information and Maintenance Log in Machine Setup section.

HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #1 (01/24/14) — PAGE 27

Image 27

Contents This Manual Must Accompany the Equipment AT ALL Times Model HTXD6i/STXD6iHTX6Di/STX6Di Trowel Table of ContentsMachine Information and Maintenance LOG Safety Messages Safety Information„ALWAYS know the location of the nearest General SafetyBefore servicing equipment Trowel SafetyEngine Safety Order Form PT-160„ Use well-insulated gloves when picking up the battery Fuel SafetyBattery Safety „ Never tamper with the factory settings„ Always shutdown engine before transporting Transporting SafetyTowing Safety LiftingEnvironmental Safety Tools Needed Machine Information ModelSerial Number General Procedures Setup Jumper InstallationRemove Setup Jumper If installed Loosen 1-1/16 jam nut on charge relief valve Item A, Figure Initial Check and AdjustmentsOIL and Coolant Check Hydraulic Oil CheckEngine Oil Engine CoolantEnsure engine is level Click Cancel again when the new screen comes up Service Tool Setup and ConnectionWST Tool Bar Input the license key obtained from Multiquip and click OKNecessary to crank or turn on the engine Laptop ConfigurationConnection Procedure Click Finish on the next screen to complete installationClick Calibration button in Pedal Sensor frame Figure Machine Setup and CalibrationSensor Adjustment Calibrate Foot PedalSecondary Hydraulic Fill Procedures CalibrationPress Start button to begin calibration and follow prompts Restart machine Machine Pressure AdjustmentCharge Pressure Adjustment Pitch Pressure CheckPitch Pressure Adjustment Steering Pressure AdjustmentReturn engine rpm to idle Turn off machine and remove gauge Lower trowel and shut off Loosen Jamb nut Item D, Figure Trowel Speed ADJUSTMENT\SETUPAdjust Zero Stroke Position Left Side Trowel Speed AdjustmentRight Side Trowel Speed Adjustment Remove setup jumper or re-enable stroke followerCalibrate Stroke Sensor Flatten Blades Pitch SetupMeasure Blade Leading Edge Height Leading Edge Height AdjustmentPitch Sensor Calibration Set Zero Pitch Cylinder StopsTurn machine off for 10 seconds GaugeInspection Fluid LevelsMechanical Static Blade Pitch Drift Test Switch smart pitch switch to off positionRefer to for location on fuse panel Fuse InformationPage HERE’S HOW to GET Help