Multiquip HTXD6i / STXD6i manual Trowel Safety, Engine Safety, Order Form PT-160

Page 6
DANGEROUS
GAS FUMES

SAFETY INFORMATION

TROWEL SAFETY

DANGER

„Engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled.

„The engine of this equipment requires an adequate free fl ow of cooling air. NEVER operate this equipment in any enclosed or narrow area

where free fl ow of the air is restricted. If the air fl ow is restricted it will cause injury

to people and property and serious damage to the equipment or engine.

„NEVER operate the equipment in an explosive atmosphere or near combustible materials.An explosion or fi re could result causing severe bodily harm or even death.

WARNING

„If applicable, NEVER use your hand to fi nd hydraulic leaks. Use a piece of wood or

cardboard. Hydraulic fl uid injected into the skin must be treated by a knowledgable physician immediately or severe injury or death can occur.

„ALWAYS keep clear of rotating or moving parts while operating the trowel.

„NEVER disconnect any emergency or safety devices. These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.

CAUTION

„NEVER allow passengers or riders on the trowel during operation.

„NEVER lubricate components or attempt service on a running machine.

„NEVER place your feet or hands inside the guard rings while starting or operating this equipment.

NOTICE

„ALWAYS keep the machine in proper running condition.

„Fix damage to machine and replace any broken parts immediately.

„ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

„A safety manual for operating and maintenance personnel of concrete power trowels produced by the Association of Equipment Manufacturers (AEM) can be obtained for a fee by ordering through their website at www.aem.org.

Order FORM PT-160

ENGINE SAFETY

WARNING

„DO NOT place hands or fingers inside engine compartment when engine is running.

„NEVER operate the engine with heat shields or guards removed.

„Keep fi ngers, hands hair and clothing away from all moving parts to prevent injury.

„DO NOT remove the radiator cap while the

engine is hot. High pressure boiling water will gush out of the radiator and severely scald any persons in the general area of the trowel.

„DO NOT remove the coolant drain plug while the engine is hot. Hot coolant will gush out of the coolant tank and severely scald any persons in the general area of the trowel.

„DO NOT remove the engine oil drain plug while the engine is hot. Hot oil will gush out of the oil tank and severely scald any persons in the general area of the trowel.

CAUTION

„NEVER touch the hot exhaust manifold, muffl er or cylinder. Allow these parts to cool

before servicing equipment.

PAGE 6 — HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #1 (01/24/14)

Image 6
Contents Model HTXD6i/STXD6i This Manual Must Accompany the Equipment AT ALL TimesTable of Contents HTX6Di/STX6Di TrowelMachine Information and Maintenance LOG Safety Information Safety MessagesGeneral Safety „ALWAYS know the location of the nearestOrder Form PT-160 Trowel SafetyEngine Safety Before servicing equipment„ Never tamper with the factory settings Fuel SafetyBattery Safety „ Use well-insulated gloves when picking up the batteryLifting Transporting SafetyTowing Safety „ Always shutdown engine before transportingEnvironmental Safety Tools Needed Machine Information ModelSerial Number General Procedures Setup Jumper InstallationRemove Setup Jumper If installed Hydraulic Oil Check Initial Check and AdjustmentsOIL and Coolant Check Loosen 1-1/16 jam nut on charge relief valve Item A, FigureEngine Oil Engine CoolantEnsure engine is level Service Tool Setup and Connection Click Cancel again when the new screen comes upInput the license key obtained from Multiquip and click OK WST Tool BarClick Finish on the next screen to complete installation Laptop ConfigurationConnection Procedure Necessary to crank or turn on the engineCalibrate Foot Pedal Machine Setup and CalibrationSensor Adjustment Click Calibration button in Pedal Sensor frame FigureSecondary Hydraulic Fill Procedures CalibrationPress Start button to begin calibration and follow prompts Pitch Pressure Check Machine Pressure AdjustmentCharge Pressure Adjustment Restart machinePitch Pressure Adjustment Steering Pressure AdjustmentReturn engine rpm to idle Turn off machine and remove gauge Left Side Trowel Speed Adjustment Trowel Speed ADJUSTMENT\SETUPAdjust Zero Stroke Position Lower trowel and shut off Loosen Jamb nut Item D, FigureRight Side Trowel Speed Adjustment Remove setup jumper or re-enable stroke followerCalibrate Stroke Sensor Pitch Setup Flatten BladesLeading Edge Height Adjustment Measure Blade Leading Edge HeightSet Zero Pitch Cylinder Stops Pitch Sensor CalibrationGauge Turn machine off for 10 secondsInspection Fluid LevelsMechanical Switch smart pitch switch to off position Static Blade Pitch Drift TestFuse Information Refer to for location on fuse panelPage HERE’S HOW to GET Help