Multiquip HTXD6i / STXD6i Fuel Safety, Battery Safety, „ Never tamper with the factory settings

Page 7

SAFETY INFORMATION

NOTICE

„NEVER run engine without an air fi lter or with a dirty air fi lter. Severe engine damage may occur. Service air fi lter frequently to prevent engine malfunction.

„NEVER tamper with the factory settings

of the engine or engine governor. Damage to the engine or equipment can result if operating in speed ranges above the maximum allowable.

FUEL SAFETY

DANGER

„DO NOT start the engine near spilled fuel or combustible fl uids. Fuel is extremely fl ammable and its vapors can cause an explosion if ignited.

„ALWAYS refuel in a well-ventilated area, away from sparks and open fl ames.

„ALWAYS use extreme caution when working with flammable liquids.

„DO NOT fi ll the fuel tank while the engine is running or hot.

„DO NOT overfi ll tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system.

„Store fuel in appropriate containers, in well-ventilated areas and away from sparks and fl ames.

„NEVER use fuel as a cleaning agent.

„DO NOT smoke around or near the equipment. Fire or explosion could result from fuel vapors or if fuel is spilled on a hot engine.

BATTERY SAFETY

DANGER

„DO NOT drop the battery. There is a possibility that the battery will explode.

„DO NOT expose the battery to open fl ames, sparks, cigarettes, etc.The battery contains combustible gases and liquids. If these

gases and liquids come into contact with a fl ame or spark, an explosion could occur.

WARNING

„ALWAYS wear safety glasses when handling the battery to avoid eye irritation. The battery contains acids that can cause injury to the eyes and skin.

„Use well-insulated gloves when picking up the battery.

„ALWAYS keep the battery charged. If the battery is not charged, combustible gas will build up.

„DO NOT charge battery if frozen. Battery can explode. When frozen, warm the battery to at least 61°F (16°C).

„ALWAYS recharge the battery in a well-ventilated environment to avoid the risk of a dangerous concentration of combustible gases.

„If the battery liquid (dilute sulfuric acid) comes into contact with clothing or skin, rinse skin or clothing immediately with plenty of water.

„If the battery liquid (dilute sulfuric acid) comes into contact with eyes, rinse eyes immediately with plenty of water and contact the nearest doctor or hospital to seek medical attention.

CAUTION

„ALWAYS disconnect the NEGATIVE battery terminal before performing service on the equipment.

„ALWAYS keep battery cables in good working condition. Repair or replace all worn cables.

HTXD6i/STXD6i TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #1 (01/24/14) — PAGE 7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents This Manual Must Accompany the Equipment AT ALL Times Model HTXD6i/STXD6iHTX6Di/STX6Di Trowel Table of ContentsMachine Information and Maintenance LOG Safety Messages Safety Information„ALWAYS know the location of the nearest General SafetyBefore servicing equipment Trowel SafetyEngine Safety Order Form PT-160„ Use well-insulated gloves when picking up the battery Fuel SafetyBattery Safety „ Never tamper with the factory settings„ Always shutdown engine before transporting Transporting SafetyTowing Safety LiftingEnvironmental Safety Tools Needed Model Machine InformationSerial Number Setup Jumper Installation General ProceduresRemove Setup Jumper If installed Loosen 1-1/16 jam nut on charge relief valve Item A, Figure Initial Check and AdjustmentsOIL and Coolant Check Hydraulic Oil CheckEngine Coolant Engine OilEnsure engine is level Click Cancel again when the new screen comes up Service Tool Setup and ConnectionWST Tool Bar Input the license key obtained from Multiquip and click OKNecessary to crank or turn on the engine Laptop ConfigurationConnection Procedure Click Finish on the next screen to complete installationClick Calibration button in Pedal Sensor frame Figure Machine Setup and CalibrationSensor Adjustment Calibrate Foot PedalCalibration Secondary Hydraulic Fill ProceduresPress Start button to begin calibration and follow prompts Restart machine Machine Pressure AdjustmentCharge Pressure Adjustment Pitch Pressure CheckSteering Pressure Adjustment Pitch Pressure AdjustmentReturn engine rpm to idle Turn off machine and remove gauge Lower trowel and shut off Loosen Jamb nut Item D, Figure Trowel Speed ADJUSTMENT\SETUPAdjust Zero Stroke Position Left Side Trowel Speed AdjustmentRemove setup jumper or re-enable stroke follower Right Side Trowel Speed AdjustmentCalibrate Stroke Sensor Flatten Blades Pitch SetupMeasure Blade Leading Edge Height Leading Edge Height AdjustmentPitch Sensor Calibration Set Zero Pitch Cylinder StopsTurn machine off for 10 seconds GaugeFluid Levels InspectionMechanical Static Blade Pitch Drift Test Switch smart pitch switch to off positionRefer to for location on fuse panel Fuse InformationPage HERE’S HOW to GET Help
Top Page Image Contents