Grizzly G0605X, G0606X owner manual Saw Blade, To install the blade

Page 24

3.Place the extension table assembly upright with the feet on the ground, align the slots in the extension table bracket with the rear rail mounting holes, then fasten the table to the rail with two M8-1.25 x 16 flange bolts and hex nuts shown in Figure 22.

Flange Bolts

Bracket

Figure 22. Outfeed table fastened to rear rail.

4.Secure the lower shelf brackets to the sup- port legs and cabinet with four M6-1 x 12 hex bolts, four flat washers and two hex nuts.

5.Install the lower shelf on the brackets.

6.Place the fence tube over the front rail and secure with nine M8-1.25 x 12 flange bolts as shown in Figure 23.

Flange Bolt

Figure 23. Fence tube mounted to front fence

rail.

Saw Blade

The saw blade is extremely sharp. Use extra care when handling the blade or working near it. Serious injury is possible.

Review this section, even if your saw blade came pre-installed.

To install the blade:

1.DISCONNECT THE SAW FROM POWER!

2.Push a piece of scrap wood against the blade to prevent the blade from rotating, then use the arbor wrench to loosen the arbor nut.

Note: The arbor nut has right hand threads; turn it counterclockwise to loosen.

3.Remove the arbor nut and the outer arbor flange.

4.Slide the blade over the arbor with the teeth facing the front of the saw as shown in Figure 24.

Teeth Direction

& Blade Rotation

Front Of Saw

Figure 24. Correct blade direction.

5.Re-install the arbor flange and the arbor nut, and tighten them against the blade with the wrench included with the saw. DO NOT over- tighten.

-22-	G0605X/G0606X Extreme Series 12" Table Saw

Image 24

Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW Identification G0606X identificationSafety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Circuit Requirements OperationAmperage Draw Circuit RequirementsGrounding Extension Cords220V Operation 440V OperationSET UP Set Up SafetyItems Needed for Set Up UnpackingMachine Inventory Fence InventoryFence Rail Inventory Extension Table Inventory Outfeed Table InventoryHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadTo install the front and rear rails Extension TableComponents and Hardware Needed Qty Foot installed on support leg To install the outfeed table Outfeed TableTo install the blade Saw BladeTo install and adjust the table insert To install the blade guardTable Insert Blade Guard SplitterOn/Off Switch To install the riving knifeTo install the switch Riving KnifeTo install the miter gauge Fence ComponentsMiter Gauge Recommended adjustment checklist Dust Collection RecommendedTest Run To connect a dust collection hosePage Operation Safety OperationsBasic Controls Disabling On/Off Switch Ripping blade featuresCrosscut blade features Combination blade featuresLaminate blade features Dado BladesNon-Through Through Cuts RippingNon-Through Cuts Through CutsTo make a crosscut using the miter gauge CrosscuttingMiter Cuts To perform a miter cutDado Cutting To use a standard saw blade to cut dadoes Rabbet Cutting To cut rabbets with the dado bladeTo cut rabbets with the standard blade Resawing Resaw BarrierComponents Needed for the Resaw Barrier Tools Needed for the Resaw BarrierAuxiliary Fence Resawing OperationsComponents Needed for the Auxiliary Fence To build the auxiliary fenceTo perform resawing operations Accessories G7895-Citrus DegreaserH1234-Table Saw Bench Guide H1300 H1298 G7984 H2347 H0736Half-mask respirator and disposable Cartridge filters G2370-SHOP FOX Board BuddiesG7581-Superbar G7582-Master Plate G3445-Precision Saw ToolH3308-SHOP FOX Push Stick H3309-SHOP FOX FeatherboardMaintenance CleaningSchedule LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Tools Needed QtyTo remove the flat belt To install the new belt Blade Tilt Stops To set the 90 stop boltTo set the 45 stop bolt To adjust the tilt indicator arrow Digital ReadoutTo set the digital readout To adjust the blade parallel to the miter slot Miter Slot to Blade ParallelismShim procedure diagram a Adjusting Fence Blade AlignmentSquare Clamping PressureParallelism If the fence is not parallel to the miter slotService Log Date Approximate Hours Of Use Service PerformedG0605X/G0606X Electrical Components G0605X motor junction boxG0605X Wiring Diagram G0606X magnetic switch prewired to Phase G0606X Electrical ComponentsG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Cabinet, Motor & Main Table Parts List DescriptionDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page