Grizzly G0605X, G0606X owner manual Machine Data Sheet

Page 6

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901

MODEL G0605X 12" EXTREME SERIES TABLE SAW

Overall Dimensions:
Table Height		353⁄4"
Table Size		303⁄4" D x 241⁄2" W
Table Size w/Extension		303⁄4" D x 783⁄4" W
Overall Size when Fully Assembled		91" W x 93" L x 421⁄2"H
Miter Gauge T-Slot		3⁄4" W x 3⁄8" D
Blade Tilt		Left 0-45°
Shipping Weight (5 Boxes)		967 lbs.
Machine Weight		715 lbs.
Footprint		581⁄2" W x 661⁄2" L
Cutting Capacities:
Blade Size		12"
Maximum Depth Of Cut @ 90°		4"
Maximum Depth Of Cut @ 45°		23⁄4"
Maximum Rip Capacity To Right Of Blade		52"
Distance From Front Of Table To Center Of Blade		171⁄4"
Distance From Front Of Table To Front Of Blade		131⁄2"
Maximum Width Of Dado Cut		1"
Motor:
Type		TEFC Capacitor Start Induction
Horsepower		5 HP
Phase/Cycle		Single-Phase/60 Hz
Voltage		220V
Amps		23A
RPM		3450
Power Transfer		Belt Drive
Power Switch		On/Off Push Button, Magnetic
Construction:
Main Table		Precision-Ground Cast Iron
Cabinet		Pre-Formed Steel
Miter Gauge		Aluminum Body/Steel Miter Bar
Trunnions		Cast Iron
Bearings		Sealed & Permanently Lubricated
Fence	T-Shape, Front Locking, Aluminum Extruded Body
Arbor Shaft:
Dimensions		1" Diameter
Speed		3600 RPM

Features:

........................................... Included Outfeed & Extension Tables w/Storage Shelves

.......................................................................................................... Digital Tilt Gauge

.......................................................................................... Quick Release Riving Knife

......................................................................................... Quick Release Blade Guard

......................................................................................................Hinged Motor Cover

...................................................................................................................4" Dust Port

........................................................................................................Included 12" Blade

Specifications, while deemed accurate, are not guaranteed.

-4-	G0605X/G0606X Extreme Series 12" Table Saw

Image 6

Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW Identification G0606X identificationSafety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Amperage Draw Circuit RequirementsOperation Circuit Requirements220V Operation GroundingExtension Cords 440V OperationItems Needed for Set Up SET UPSet Up Safety UnpackingMachine Inventory Fence InventoryFence Rail Inventory Extension Table Inventory Outfeed Table InventoryHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadTo install the front and rear rails Extension TableComponents and Hardware Needed Qty Foot installed on support leg To install the outfeed table Outfeed TableTo install the blade Saw BladeTable Insert To install and adjust the table insertTo install the blade guard Blade Guard SplitterTo install the switch On/Off SwitchTo install the riving knife Riving KnifeTo install the miter gauge Fence ComponentsMiter Gauge Test Run Recommended adjustment checklistDust Collection Recommended To connect a dust collection hosePage Operation Safety OperationsBasic Controls Crosscut blade features Disabling On/Off SwitchRipping blade features Combination blade featuresLaminate blade features Dado BladesNon-Through Cuts Non-Through Through CutsRipping Through CutsTo make a crosscut using the miter gauge CrosscuttingMiter Cuts To perform a miter cutDado Cutting To use a standard saw blade to cut dadoes Rabbet Cutting To cut rabbets with the dado bladeTo cut rabbets with the standard blade Components Needed for the Resaw Barrier ResawingResaw Barrier Tools Needed for the Resaw BarrierComponents Needed for the Auxiliary Fence Auxiliary FenceResawing Operations To build the auxiliary fenceTo perform resawing operations H1234-Table Saw Bench Guide AccessoriesG7895-Citrus Degreaser H1300 H1298 G7984 H2347 H0736Half-mask respirator and disposable Cartridge filters G2370-SHOP FOX Board BuddiesH3308-SHOP FOX Push Stick G7581-Superbar G7582-Master PlateG3445-Precision Saw Tool H3309-SHOP FOX FeatherboardSchedule MaintenanceCleaning LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Tools Needed QtyTo remove the flat belt To install the new belt Blade Tilt Stops To set the 90 stop boltTo set the 45 stop bolt To adjust the tilt indicator arrow Digital ReadoutTo set the digital readout To adjust the blade parallel to the miter slot Miter Slot to Blade ParallelismShim procedure diagram a Square Adjusting FenceBlade Alignment Clamping PressureParallelism If the fence is not parallel to the miter slotService Log Date Approximate Hours Of Use Service PerformedG0605X/G0606X Electrical Components G0605X motor junction boxG0605X Wiring Diagram G0606X magnetic switch prewired to Phase G0606X Electrical ComponentsG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Cabinet, Motor & Main Table Parts List DescriptionDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page