Grizzly G0605X, G0606X owner manual Table Saw Operations

Page 48

Symptom

Possible Cause

Possible Solution

Machine has vibra-

1.

Motor or component is loose.

1.

Inspect/replace stripped or damaged bolts/nuts, and

tion or noisy opera-

 

 

 

re-tighten with thread locking fluid.

tion.

2.

Flat belt worn or loose.

2.

Inspect/replace flat belt with new one (refer to Page

 

 

 

 

 

47).

 

3.

Motor fan is rubbing on fan cover.

3.

Replace dented fan cover; replace loose/damaged

 

 

 

 

fan.

 

4.

Pulley is loose.

4.

Realign/replace shaft, pulley, set screw, and key as

 

 

 

 

required.

 

5.

Machine sits unevenly on floor.

5.

Relocate/shim machine.

 

6.

Arbor bearings are at fault.

6.

Replace arbor housing bearings; replace arbor.

 

7.

Arbor pulley is loose.

7.

Retighten/replace arbor pulley with shaft and thread

 

 

 

 

locking liquid.

 

8.

Workpiece is loose.

8.

Use the correct holding fixture and reclamp

 

 

 

 

workpiece.

 

9.

Motor bearings are at fault.

9.

Test by rotating shaft; rotational grinding/loose shaft

 

 

 

 

requires bearing replacement.

 

10. Blade is at fault.

10. Replace warped, bent, or twisted blade; resharpen

 

 

 

 

dull blade.

 

11. Loose arbor nut

11. Tighten the arbor nut.

 

12. Centrifugal switch (single-phase).

12. Replace centrifugal switch.

 

 

 

 

Table Saw Operations

 

 

Symptom

 

Possible Cause

Possible Solution

Blade is not aligned

1.

Blade is warped.

1.

Replace blade (Page 22).

with miter slot

or

2.

Table top is not parallel to blade.

2.

Make table parallel to blade (Page 51).

fence.

 

 

3.

Fence is not parallel to blade.

3.

Make fence parallel to blade (Page 54).

 

 

 

 

 

 

 

 

 

Blade

does not

1.

90° stop bolt is out of adjustment.

1.

Adjust 90° stop bolt (Page 49).

reach 90°.

 

2.

Sawdust loaded up on positive stop.

2.

Clean sawdust off positive stop.

 

 

 

 

 

 

 

Blade

hits insert

at

1.

45° stop bolt is out of adjustment.

1.

Adjust 45° stop bolt (Page 49).

45°.

 

 

2.

Hole in insert is inadequate.

2.

File or mill the hole in the insert.

 

 

 

3.

Table out of alignment.

3.

Align blade to the table (Page 51).

 

 

 

4.

Blade position is incorrect.

4.

Adjust blade position.

 

 

 

 

 

 

 

Board

binds

or

1.

Dull blade.

1.

Replace blade.

burns when feeding

2.

Blade is warped.

2.

Replace blade (Page 22).

through tablesaw.

 

3.

Fence is not parallel to blade.

3.

Make fence parallel to blade (Page 54).

 

 

 

 

 

 

4.

Table top is not parallel to blade.

4.

Make table parallel to blade (Page 51).

 

 

 

 

 

 

 

-46-

G0605X/G0606X Extreme Series 12" Table Saw

Image 48
Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW Identification G0606X identificationSafety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Circuit Requirements OperationAmperage Draw Circuit RequirementsGrounding Extension Cords220V Operation 440V OperationSET UP Set Up SafetyItems Needed for Set Up UnpackingMachine Inventory Fence InventoryFence Rail Inventory Extension Table Inventory Outfeed Table InventoryHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadTo install the front and rear rails Extension TableComponents and Hardware Needed Qty Foot installed on support leg To install the outfeed table Outfeed TableTo install the blade Saw BladeTo install and adjust the table insert To install the blade guardTable Insert Blade Guard SplitterOn/Off Switch To install the riving knifeTo install the switch Riving KnifeTo install the miter gauge Fence ComponentsMiter Gauge Recommended adjustment checklist Dust Collection RecommendedTest Run To connect a dust collection hosePage Operation Safety OperationsBasic Controls Disabling On/Off Switch Ripping blade featuresCrosscut blade features Combination blade featuresLaminate blade features Dado BladesNon-Through Through Cuts RippingNon-Through Cuts Through CutsTo make a crosscut using the miter gauge CrosscuttingMiter Cuts To perform a miter cutDado Cutting To use a standard saw blade to cut dadoes Rabbet Cutting To cut rabbets with the dado bladeTo cut rabbets with the standard blade Resawing Resaw BarrierComponents Needed for the Resaw Barrier Tools Needed for the Resaw BarrierAuxiliary Fence Resawing OperationsComponents Needed for the Auxiliary Fence To build the auxiliary fenceTo perform resawing operations Accessories G7895-Citrus DegreaserH1234-Table Saw Bench Guide H1300 H1298 G7984 H2347 H0736Half-mask respirator and disposable Cartridge filters G2370-SHOP FOX Board BuddiesG7581-Superbar G7582-Master Plate G3445-Precision Saw ToolH3308-SHOP FOX Push Stick H3309-SHOP FOX FeatherboardMaintenance CleaningSchedule LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Tools Needed QtyTo remove the flat belt To install the new belt Blade Tilt Stops To set the 90 stop boltTo set the 45 stop bolt To adjust the tilt indicator arrow Digital ReadoutTo set the digital readout To adjust the blade parallel to the miter slot Miter Slot to Blade ParallelismShim procedure diagram a Adjusting Fence Blade AlignmentSquare Clamping PressureParallelism If the fence is not parallel to the miter slotService Log Date Approximate Hours Of Use Service PerformedG0605X/G0606X Electrical Components G0605X motor junction boxG0605X Wiring Diagram G0606X magnetic switch prewired to Phase G0606X Electrical ComponentsG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Cabinet, Motor & Main Table Parts List DescriptionDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page