Grizzly G0605X Riving Knife, On/Off Switch, To install the riving knife, To install the switch

Page 26

5.Slide the bracket screws shown in Figure 28 into the notches on the splitter, push the guard forward, and tighten the lock knob (Figure 29).

Note: Make sure the clear plastic flap is pushed toward the inside of the guard.

Screws

Notches

Figure 28. Installing blade guard on splitter.

Lock knob

Cover

Flap

Figure 29. Blade guard installed.

6.Swing the covers down to guard the blade.

Riving Knife

You MUST install the riving knife or the splitter and blade guard before operating the table saw.

Components and Hardware Needed:

Qty

Riving Knife

1

To install the riving knife:

 

1.Remove the table insert, blade guard, and splitter—if previously installed.

2.Lift the lever (Figure 30), insert the riving knife into the bracket slot, and turn the lever down to secure the knife.

3.Reinstall and secure the table insert.

Riving Knife

Bracket

Lever

Figure 30. Riving knife installed.

 

On/Off Switch

 

Components and Hardware Needed:

Qty

Safety Pin

1

Flange Bolts M8-1.25 x 25

2

To install the switch:

 

1.Fasten the switch to the left end of the front rail with two flange bolts, and install the anti- start safety pin as shown in Figure 31.

-24-

G0605X/G0606X Extreme Series 12" Table Saw

Image 26
Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Contact Info IntroductionForeword Machine Data Sheet Model G0606X 12 Extreme Series Table SAW Identification G0606X identificationSafety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Below are tips to avoid the most common causes of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Amperage Draw Circuit RequirementsOperation Circuit Requirements220V Operation GroundingExtension Cords 440V OperationItems Needed for Set Up SET UPSet Up Safety UnpackingFence Rail Inventory Machine InventoryFence Inventory Extension Table Inventory Outfeed Table InventoryHardware Recognition Chart Site Considerations Clean UpPlacement Location Floor LoadComponents and Hardware Needed Qty To install the front and rear railsExtension Table Foot installed on support leg To install the outfeed table Outfeed TableTo install the blade Saw BladeTable Insert To install and adjust the table insertTo install the blade guard Blade Guard SplitterTo install the switch On/Off SwitchTo install the riving knife Riving KnifeMiter Gauge To install the miter gaugeFence Components Test Run Recommended adjustment checklistDust Collection Recommended To connect a dust collection hosePage Basic Controls Operation SafetyOperations Crosscut blade features Disabling On/Off SwitchRipping blade features Combination blade featuresLaminate blade features Dado BladesNon-Through Cuts Non-Through Through CutsRipping Through CutsTo make a crosscut using the miter gauge CrosscuttingMiter Cuts To perform a miter cutDado Cutting To use a standard saw blade to cut dadoes Rabbet Cutting To cut rabbets with the dado bladeTo cut rabbets with the standard blade Components Needed for the Resaw Barrier ResawingResaw Barrier Tools Needed for the Resaw BarrierComponents Needed for the Auxiliary Fence Auxiliary FenceResawing Operations To build the auxiliary fenceTo perform resawing operations H1234-Table Saw Bench Guide AccessoriesG7895-Citrus Degreaser H1300 H1298 G7984 H2347 H0736Half-mask respirator and disposable Cartridge filters G2370-SHOP FOX Board BuddiesH3308-SHOP FOX Push Stick G7581-Superbar G7582-Master PlateG3445-Precision Saw Tool H3309-SHOP FOX FeatherboardSchedule MaintenanceCleaning LubricationMotor & Electrical ServiceTroubleshooting Table Saw Operations To remove the flat belt Replacing Flat BeltTools Needed Qty To install the new belt To set the 45 stop bolt Blade Tilt StopsTo set the 90 stop bolt To set the digital readout To adjust the tilt indicator arrowDigital Readout To adjust the blade parallel to the miter slot Miter Slot to Blade ParallelismShim procedure diagram a Square Adjusting FenceBlade Alignment Clamping PressureParallelism If the fence is not parallel to the miter slotService Log Date Approximate Hours Of Use Service PerformedG0605X/G0606X Electrical Components G0605X motor junction boxG0605X Wiring Diagram G0606X magnetic switch prewired to Phase G0606X Electrical ComponentsG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Cabinet, Motor & Main Table Parts List DescriptionDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page