Grizzly G0606X, G0605X owner manual Extension Table Assembly

Page 69

Extension Table Assembly Breakdown

��

��

��

��

��

��

��

			��
		��
��			��
��
��
��	��
��	��
��	��
��
��			��
			��
��	��	��	��	��
��	��	��	��	��
		��	��	��
				��
��
					��
				��	��
��				��	��
				��
			��

Extension Table Parts List

REF	PART #	DESCRIPTION

500	P0605X500	EXTENSION TABLE ASSEMBLY

501	P0605X501	LEFT SCALE

502	P0605X502	RIGHT SCALE

503	P0605X503	EXTENSION TABLE PLATE

504	P0605X504	EXTENSION TABLE SUPPORT

505	P0605X505	FRONT EXTENSION BRACKET

506	P0605X506	FRONT RAIL (91-3/8" LONG)

507	P0605X507	FENCE TUBE (91-3/8" LONG)

508	P0605X508	END CAP

509	P0605X509	REAR RAIL (79" LONG)

510	P0605X510	REAR EXTENSION BRACKET

511	P0605X511	LOWER SHELF

512	P0605X512	LOWER SHELF BRACKET

513	P0605X513	SHELF END PLATE

514	P0605X514	SUPPORT LEG

515	PHTEK6M	TAP SCREW M4 X 16

REF	PART #	DESCRIPTION

523	P0605X523	FRONT RAIL PLATE 52"

526	P0605X526	RIGHT EXTENSION PLATE

529	PS14M	PHLP HD SCR M6-1 X 12

530	PW03M	FLAT WASHER 6MM

531	PW04M	FLAT WASHER 10MM

532	PN01M	HEX NUT M6-1

533	PN08	HEX NUT 3/8-16

534	P0605X534	FOOT 3/8-16 X 2

535	PB32M	HEX BOLT M10-1.5 X 25

536	PS14M	PHLP HD SCR M6-1 X 12

538	PFH21M	FLAT HD SCR M8-1.25 X 25

539	PFB15M	FLANGE BOLT M8-1.25 X 12

540	PLW04M	LOCK WASHER 8MM

541	PSB31M	CAP SCREW M8-1.25 X 25

542	PW01M	FLAT WASHER 8MM

543	PN03M	HEX NUT M8-1.25

G0605X/G0606X Extreme Series 12" Table Saw

-67-

Image 69

Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW G0606X identification IdentificationSafety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Operation Circuit RequirementsAmperage Draw Circuit RequirementsExtension Cords Grounding220V Operation 440V OperationSet Up Safety SET UPItems Needed for Set Up UnpackingMachine Inventory Fence InventoryFence Rail Inventory Outfeed Table Inventory Extension Table InventoryHardware Recognition Chart Placement Location Clean UpSite Considerations Floor LoadTo install the front and rear rails Extension TableComponents and Hardware Needed Qty Foot installed on support leg Outfeed Table To install the outfeed tableSaw Blade To install the bladeTo install the blade guard To install and adjust the table insertTable Insert Blade Guard SplitterTo install the riving knife On/Off SwitchTo install the switch Riving KnifeTo install the miter gauge Fence ComponentsMiter Gauge Dust Collection Recommended Recommended adjustment checklistTest Run To connect a dust collection hosePage Operation Safety OperationsBasic Controls Ripping blade features Disabling On/Off SwitchCrosscut blade features Combination blade featuresDado Blades Laminate blade featuresRipping Non-Through Through CutsNon-Through Cuts Through CutsCrosscutting To make a crosscut using the miter gaugeTo perform a miter cut Miter CutsDado Cutting To use a standard saw blade to cut dadoes To cut rabbets with the dado blade Rabbet CuttingTo cut rabbets with the standard blade Resaw Barrier ResawingComponents Needed for the Resaw Barrier Tools Needed for the Resaw BarrierResawing Operations Auxiliary FenceComponents Needed for the Auxiliary Fence To build the auxiliary fenceTo perform resawing operations G7895-Citrus Degreaser AccessoriesH1234-Table Saw Bench Guide H1300 H1298 G7984 H2347 H0736G2370-SHOP FOX Board Buddies Half-mask respirator and disposable Cartridge filtersG3445-Precision Saw Tool G7581-Superbar G7582-Master PlateH3308-SHOP FOX Push Stick H3309-SHOP FOX FeatherboardCleaning MaintenanceSchedule LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Tools Needed QtyTo remove the flat belt To install the new belt Blade Tilt Stops To set the 90 stop boltTo set the 45 stop bolt To adjust the tilt indicator arrow Digital ReadoutTo set the digital readout Miter Slot to Blade Parallelism To adjust the blade parallel to the miter slotShim procedure diagram a Blade Alignment Adjusting FenceSquare Clamping PressureIf the fence is not parallel to the miter slot ParallelismDate Approximate Hours Of Use Service Performed Service LogG0605X motor junction box G0605X/G0606X Electrical ComponentsG0605X Wiring Diagram G0606X Electrical Components G0606X magnetic switch prewired to PhaseG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Description Cabinet, Motor & Main Table Parts ListDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page