Grizzly G0605X Digital Readout, To adjust the tilt indicator arrow, To set the digital readout

Page 52

4.Loosen the jam nut (Figure 77) on the 45° stop bolt, adjust the stop bolt up or down, then check to see if the blade is 45° to the table.

45° Stop Bolt

Jam Nut

Figure 77. 45° stop bolt and jam nut.

5.Continue adjusting the stop bolt until it con- tacts the cabinet when the blade is at 45°.

6.Tighten the jam nut.

To adjust the tilt indicator arrow:

1.Set the 90° stop bolt (see instructions on Page 49).

2.Loosen the blade height handwheel set screw and remove the handwheel.

3.Loosen the button head cap screw shown in Figure 78 and move the tip of the indicator to 0°.

Indicator

Button Head

Cap Screw

 

Figure 78. Tilt indicator arrow.

4.

Tighten the cap screw and reinstall the

 

handwheel.

-50-

Digital Readout

The digital readout displays the current blade angle. We recommend you set the readout after verifying the 90° and 45° blade tilt stops.

To set the digital readout:

1.Move the blade angle to 0° and press the 0° SET button (Figure 79) for several seconds until the readout displays 0.00.

0° Set Button

45° Set Button

Figure 79. Digital readout.

2.Move the blade angle to 45° and press the SET button for several seconds until the readout displays 45.0.

Note: If you move the blade angle handwheel when the power is disconnected, the digital readout will be incorrect when the saw is reconnected.

G0605X/G0606X Extreme Series 12" Table Saw

Image 52
Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Foreword IntroductionContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW Identification G0606X identificationSafety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Protecting Yourself From Kickback Preventing KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Circuit Requirements OperationAmperage Draw Circuit RequirementsGrounding Extension Cords220V Operation 440V OperationSET UP Set Up SafetyItems Needed for Set Up UnpackingFence Inventory Machine InventoryFence Rail Inventory Extension Table Inventory Outfeed Table InventoryHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadExtension Table To install the front and rear railsComponents and Hardware Needed Qty Foot installed on support leg To install the outfeed table Outfeed TableTo install the blade Saw BladeTo install and adjust the table insert To install the blade guardTable Insert Blade Guard SplitterOn/Off Switch To install the riving knifeTo install the switch Riving KnifeFence Components To install the miter gaugeMiter Gauge Recommended adjustment checklist Dust Collection RecommendedTest Run To connect a dust collection hosePage Operations Operation SafetyBasic Controls Disabling On/Off Switch Ripping blade featuresCrosscut blade features Combination blade featuresLaminate blade features Dado BladesNon-Through Through Cuts RippingNon-Through Cuts Through CutsTo make a crosscut using the miter gauge CrosscuttingMiter Cuts To perform a miter cutDado Cutting To use a standard saw blade to cut dadoes Rabbet Cutting To cut rabbets with the dado bladeTo cut rabbets with the standard blade Resawing Resaw BarrierComponents Needed for the Resaw Barrier Tools Needed for the Resaw BarrierAuxiliary Fence Resawing OperationsComponents Needed for the Auxiliary Fence To build the auxiliary fenceTo perform resawing operations Accessories G7895-Citrus DegreaserH1234-Table Saw Bench Guide H1300 H1298 G7984 H2347 H0736Half-mask respirator and disposable Cartridge filters G2370-SHOP FOX Board BuddiesG7581-Superbar G7582-Master Plate G3445-Precision Saw ToolH3308-SHOP FOX Push Stick H3309-SHOP FOX FeatherboardMaintenance CleaningSchedule LubricationTroubleshooting ServiceMotor & Electrical Table Saw Operations Tools Needed Qty Replacing Flat BeltTo remove the flat belt To install the new belt To set the 90 stop bolt Blade Tilt StopsTo set the 45 stop bolt Digital Readout To adjust the tilt indicator arrowTo set the digital readout To adjust the blade parallel to the miter slot Miter Slot to Blade ParallelismShim procedure diagram a Adjusting Fence Blade AlignmentSquare Clamping PressureParallelism If the fence is not parallel to the miter slotService Log Date Approximate Hours Of Use Service PerformedG0605X/G0606X Electrical Components G0605X motor junction boxG0605X Wiring Diagram G0606X magnetic switch prewired to Phase G0606X Electrical ComponentsG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Cabinet, Motor & Main Table Parts List DescriptionDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page