Grizzly G0605X owner manual G0606X Electrical Components, G0606X magnetic switch prewired to Phase

Page 60

G0606X Electrical Components

Figure 93. G0606X magnetic switch prewired to 220V,

3-phase.

Figure 94. G0606X magnetic switch converted to

440V, 3-phase.

Note: Thee thermal relay in Figure 93 is set for 22 amp, 220V, 3-phase operation.

Note: The therrmal relay in Figure 94 is adjusted for 11 amp, 440V, 3-phase operation.

-58-	G0605X/G0606X Extreme Series 12" Table Saw

Image 60

Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW Identification G0606X identificationSafety Safety Instructions for MachineryAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Circuit Requirements OperationAmperage Draw Circuit RequirementsGrounding Extension Cords220V Operation 440V OperationSET UP Set Up SafetyItems Needed for Set Up UnpackingMachine Inventory Fence InventoryFence Rail Inventory Extension Table Inventory Outfeed Table InventoryHardware Recognition Chart Clean Up Placement LocationSite Considerations Floor LoadTo install the front and rear rails Extension TableComponents and Hardware Needed Qty Foot installed on support leg To install the outfeed table Outfeed TableTo install the blade Saw BladeTo install and adjust the table insert To install the blade guardTable Insert Blade Guard SplitterOn/Off Switch To install the riving knifeTo install the switch Riving KnifeTo install the miter gauge Fence ComponentsMiter Gauge Recommended adjustment checklist Dust Collection RecommendedTest Run To connect a dust collection hosePage Operation Safety OperationsBasic Controls Disabling On/Off Switch Ripping blade featuresCrosscut blade features Combination blade featuresLaminate blade features Dado BladesNon-Through Through Cuts RippingNon-Through Cuts Through CutsTo make a crosscut using the miter gauge CrosscuttingMiter Cuts To perform a miter cutDado Cutting To use a standard saw blade to cut dadoes Rabbet Cutting To cut rabbets with the dado bladeTo cut rabbets with the standard blade Resawing Resaw BarrierComponents Needed for the Resaw Barrier Tools Needed for the Resaw BarrierAuxiliary Fence Resawing OperationsComponents Needed for the Auxiliary Fence To build the auxiliary fenceTo perform resawing operations Accessories G7895-Citrus DegreaserH1234-Table Saw Bench Guide H1300 H1298 G7984 H2347 H0736Half-mask respirator and disposable Cartridge filters G2370-SHOP FOX Board BuddiesG7581-Superbar G7582-Master Plate G3445-Precision Saw ToolH3308-SHOP FOX Push Stick H3309-SHOP FOX FeatherboardMaintenance CleaningSchedule LubricationService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Tools Needed QtyTo remove the flat belt To install the new belt Blade Tilt Stops To set the 90 stop boltTo set the 45 stop bolt To adjust the tilt indicator arrow Digital ReadoutTo set the digital readout To adjust the blade parallel to the miter slot Miter Slot to Blade ParallelismShim procedure diagram a Adjusting Fence Blade AlignmentSquare Clamping PressureParallelism If the fence is not parallel to the miter slotService Log Date Approximate Hours Of Use Service PerformedG0605X/G0606X Electrical Components G0605X motor junction boxG0605X Wiring Diagram G0606X magnetic switch prewired to Phase G0606X Electrical ComponentsG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Cabinet, Motor & Main Table Parts List DescriptionDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page