Grizzly G0606X, G0605X owner manual Fence Components, Miter Gauge, To install the miter gauge

Page 27

Flange Bolt

Stop Paddle

Fence Components

Components and Hardware Needed:	Qty
Fence Knob	1
Fence Resting Brackets	2
Flange Bolts M8-1.25 x 12	2

Anti-Start
Safety Pin
Figure 31. Switch installed.
Miter Gauge
Components and Hardware Needed:	Qty
Miter Gauge	1
Miter Gauge Handle	1
Flat Washer 8mm	1
To install the miter gauge:

1.Install the miter gauge handle and 8mm flat washer onto the miter gauge as shown in Figure 32.

Handle

Washer

Figure 32. Miter gauge installed.

2.Slide the miter gauge into the miter gauge slot to the left of the blade; or store it tempo- rarily on the brackets near the blade angle handwheel.

G0605X/G0606X Extreme Series 12" Table Saw

To install the fence knobs, fence, and fence resting brackets:

1.Install the fence knob as shown in Figure 33.

Figure 33. Fence knob installed.

2.Install the fence onto the table to the right of the blade.

3.Install the fence resting brackets (Figure 34) onto the cabinet under the Outfeed Table with two flange bolts.

Brackets

Figure 34. Fence resting brackets installed.

-25-

Image 27

Contents Extreme Series Table SAW Page Table of Contents Accessories Maintenance Introduction ForewordContact Info Machine Data Sheet Model G0606X 12 Extreme Series Table SAW G0606X identification IdentificationSafety Instructions for Machinery SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Circuit Requirements Circuit RequirementsOperation Amperage Draw440V Operation GroundingExtension Cords 220V OperationUnpacking SET UPSet Up Safety Items Needed for Set UpMachine Inventory Fence InventoryFence Rail Inventory Outfeed Table Inventory Extension Table InventoryHardware Recognition Chart Floor Load Clean UpPlacement Location Site ConsiderationsTo install the front and rear rails Extension TableComponents and Hardware Needed Qty Foot installed on support leg Outfeed Table To install the outfeed tableSaw Blade To install the bladeBlade Guard Splitter To install and adjust the table insertTo install the blade guard Table InsertRiving Knife On/Off SwitchTo install the riving knife To install the switchTo install the miter gauge Fence ComponentsMiter Gauge To connect a dust collection hose Recommended adjustment checklistDust Collection Recommended Test RunPage Operation Safety OperationsBasic Controls Combination blade features Disabling On/Off SwitchRipping blade features Crosscut blade featuresDado Blades Laminate blade featuresThrough Cuts Non-Through Through CutsRipping Non-Through CutsCrosscutting To make a crosscut using the miter gaugeTo perform a miter cut Miter CutsDado Cutting To use a standard saw blade to cut dadoes To cut rabbets with the dado blade Rabbet CuttingTo cut rabbets with the standard blade Tools Needed for the Resaw Barrier ResawingResaw Barrier Components Needed for the Resaw BarrierTo build the auxiliary fence Auxiliary FenceResawing Operations Components Needed for the Auxiliary FenceTo perform resawing operations H1300 H1298 G7984 H2347 H0736 AccessoriesG7895-Citrus Degreaser H1234-Table Saw Bench GuideG2370-SHOP FOX Board Buddies Half-mask respirator and disposable Cartridge filtersH3309-SHOP FOX Featherboard G7581-Superbar G7582-Master PlateG3445-Precision Saw Tool H3308-SHOP FOX Push StickLubrication MaintenanceCleaning ScheduleService TroubleshootingMotor & Electrical Table Saw Operations Replacing Flat Belt Tools Needed QtyTo remove the flat belt To install the new belt Blade Tilt Stops To set the 90 stop boltTo set the 45 stop bolt To adjust the tilt indicator arrow Digital ReadoutTo set the digital readout Miter Slot to Blade Parallelism To adjust the blade parallel to the miter slotShim procedure diagram a Clamping Pressure Adjusting FenceBlade Alignment SquareIf the fence is not parallel to the miter slot ParallelismDate Approximate Hours Of Use Service Performed Service LogG0605X motor junction box G0605X/G0606X Electrical ComponentsG0605X Wiring Diagram G0606X Electrical Components G0606X magnetic switch prewired to PhaseG0606X Wiring Diagram G0606X Wiring Diagram Cabinet, Motor & Main Table Breakdown Description Cabinet, Motor & Main Table Parts ListDescription Blade Guard Assembly Breakdown Blade Guard Parts List Fence Assembly Breakdown Fence Parts List Miter Gauge Assembly Breakdown Miter Gauge Parts List Extension Table Assembly Outfeed Table Assembly Breakdown Outfeed Table Parts List Guard and ANTI-KICK Back Label Warranty and Returns Page Page