Woodstock W1820, W1819 manual `m`eBe`

FG<I8K@FEJ

	Df[\cN(/(0&N(/)'D]^%J`eZ\('&('
I`m`e^Be`]\
The riving knife works in the same manner as the spread-
er on the blade guard assembly. It is a metal plate that	D`e`dld(dd	?\`^_k;`]]\i\eZ\
prevents the newly cut workpiece from pinching the back-	DXo`dld,dd
side of the blade and causing kickback.
The key difference between the spreader and the riving
knife is that the riving knife mounts below the blade's			I`m`e^
highest point of rotation, as shown in =`^li\+0.
				Be`]\
The height difference between the riving knife and the
	=`^li\+0% Height difference between
blade allows the workpiece to pass over the blade during	riving knife and blade.
non-through cuts (those in which the blade does not cut
all the way through the thickness of the workpiece).	Kfg;`jkXeZ\
	D`e`dld*dd
The riving knife acts as a barrier behind the blade to	DXo`dld/dd
reduce the risk of hands being pulled into the blade if
a kickback occurs. The riving knife must be kept within				I`m`e^
the range shown in Figure 50. For that reason, we only	9fkkfd;`jkXeZ\
recommend using a 10" blade for operations that require				Be`]\
	D`e`dld*dd
use of the riving knife.	DXo`dld/dd
?fnkf@ejkXcck_\I`m`e^Be`]\		KXYc\
	=`^li\ ,'. Allowable top and bottom
The riving knife is installed in a similar manner to the
	distances between riving knife and blade.
blade guard and spreader. Refer to Blade Guard on GX^\
*- for installation instructions.
N_\ekfLj\k_\I`m`e^Be`]\
	@e fi[\i kf nfib gifg\icp# k_\ i`m`e^
Use the riving knife for all non-through cuts made with	be`]\ ZXeefk Y\ Y\ek fi d`jXc`^e\[
	n`k_ k_\ YcX[\% @] k_\ i`m`e^ be`]\ ^\kj
a standard table saw blade (i.e., dadoes or rabbet cuts
	XZZ`[\ekXccp Y\ek# kXb\ k_\ k`d\ kf
in which a dado blade is NOT used, and when using a
	jkiX`^_k\e `k fi aljk i\gcXZ\ `k% Lj`e^
tenoning jig). Also, use the riving knife for those special
	X Y\ek fi d`jXc`^e\[ i`m`e^ be`]\ n`cc
operations where the blade guard or its components get
	`eZi\Xj\k_\i`jbf]b`ZbYXZb
in the way of safe operation, such as with very narrow
cuts.
When Not to Use the Riving Knife
The riving knife CANNOT be used with a dado blade	To ensure riving knife works safely, the
that has a diameter smaller than 10." Otherwise, the	following requirements MUST be met
riving knife height will exceed the blade height and the	when installing new blades:
workpiece will hit the riving knife during the cut, forcing	› 9cX[\;`Xd\k\i1('
the operator into a dangerous situation of trying to turn	› I`m`e^Be`]\K_`Zbe\jj1'%()%,dd
the saw off with the workpiece stuck halfway through the	› I\hl`i\[ 9cX[\ 9f[p			K_`Zbe\jj
cut.	\oZcl[`e^k\\k_ 1'%'.(Æ'%'0+(%/Æ
In addition, although it is possible to use the riving knife	)%+dd
	› I\hl`i\[ 9cX[\ B\i] K_`Zbe\jj1
for through cutting operations, the blade guard assembly	'%(')Æ'%()-)%-ddÆ*%)dd 
offers far more injury protection and risk reduction than	 Iiving knife MUST be aligned to blade;
the riving knife. Therefore, we strongly recommend that	K_\j\ I\hl`i\d\ekj [f efk Xggcp kf
you use the blade guard assembly instead of the riving	[X[fYcX[\j%
knife for through cuts.
-38-