Woodstock W1812 manual FGI8K@FEJ

Page 25

N(/()Fne\ijDXelXcD]^%j`eZ\*&'0

—If a certain moulding knife profile does not allow you to adjust the outfeed roller down far enough for proper roller traction, the eccentric stop must be repositioned to the lower hole. To do this, remove the jam nut (Figure 28), reposition the eccentric stop (Figure 29) in the lower hole, and finger tighten the jam nut. Next rotate the eccen- tric stop to lower or raise the roller and retighten the jam nut.

Lower

Jam Nut

Hole

FG<I8K@FEJ

3. Loosen and back off the four spring tensioner jam nuts (=`^li\30) completely, and unthread the ten- sioner assemblies until you are sure that they are not touching the springs.

+. Thread the tensioners back into the housings until you feel the tensioner just contact the springs.

,. Give each tensioner approximately two full turns to preload the springs and tighten the jam nuts.

-. Reinstall the chip deflector.

=`^li\28.Feed roller stop adjustment.

Eccentric Stop

=`^li\29.Eccentric stop.

=`^li\30.Feed roller tension adjustment.

-22-

Image 25

Contents

DLCGHB6CJ6A Model W1812 Variable Speed Planer Moulder With Stand Page @EKIFLK@FE Fek\ekjNffjkfZbK\Ze`ZXcJlggfik @EKIFLK@FEJ8=KP FekifcjXe=\Xkli\jB68=C HE886IDCH Lkk\i\X @efidXk`fe J8=KP D8BJLIL8IJ8I@EGC88ENFIBFIIKCP9=FILJ@ED8?@EIP% `k`feXcJX\kpfiGcXe\i&Dflc\ij Ok\ej`fefij Fg\iXk`fe\Zki`ZXcJg\Z``ZXk`fej @em\ekfip LegXZb`e9fo@em\ekfip=`li\3 \Xe`eDXZ`e\ DXZ`e\GcXZ\d\ekDflek`ekfJfg=cffi `k`eXeDfm`eKfXjj\dYc\k\gcXe\i&dflc\i#fk\j\jk\gj1 8jj\dYcpJklg Loom \Zfdd\e\=DXkljkGfik1%%%%%%%%%%%%%%%% +=D Ljkfcc\Zk`feKfk\jkilek\dXZ`e\#fk\j\jk\gj1 \jkIle\e\iXc FGI8K@FEJ@ejkXcc`eGcXe`eBe`m\j Disconnect the PLANER/MOULDER from PowerKf`ejkXccdflc`ebe`m\j#fk\j\jk\gj1 @ejkXcc`eDflc`eBe`m\jKfXaljkk\\\ifcc\ijgi`ek\ej`fe#fk\j\jk\gj1 =\\Ifcc\i?\`kXe Jgi`eK\ej`feFGI8K@FEJ ?8I Nfibg`\Z\@ejg\Zk`feDlck`gc\9fXi?XqXi GcXe`efjXefekjAvoiding Kickback GcXe`eFg\iXk`fe\ =fid`e Be`\ c\XiXeZ\ Dflc`e f j Xe fe kjIfneDflc`eJlggfik `q\Nfibg`\Z\8ggifgi`Xk\cp \Dflc`eKXccNfibg`\Z\j Dflc`eFg\iXk`fe Df\c**0*Çcc`gk`ZXcA` 8JJFI@J+0ÇCXi\ljkfcc\Zk`feJ\gXiXkfi Çljkfcc\ZkfiDf\c.*ÇJ`ec\Ifcc\iJkXe Df\c.+Ç,Ifcc\iJkXe\Xe`e=\\Dfkfi \Xe`eKXYc\Xe9Xj\ KfclYi`ZXk\k\dXZ`e\#fk\j\jk\gj1 ClYi`ZXk`feTo replace feed motor brushes, do these steps Xe`e=\\Dfkfi 9ilj\jKfZ\Zbk\\\ifcc\i$kf$kXYc\Xc`ed\ek#fk\j\ jk\gj1 =\\Ifcc\i$kf$KXYc\ 8c`ed\ek`m\X`e8aljkd\ek To adjust the drive chain slack, do these steps`Y 8aljkd\ek \Zki`ZXcJX\kp@ejkilZk`fej Wiring Diagram Color KEY`i`e `XiXd \Zki`ZXcfdgfe\ekCfZXk`fej GIF9CD KiflYc\jffk`eRemove/replace brushes Excessive snipe there is ?\XjkfZb G8IKJ?\XjkfZbGXikjC`jk DX`eDfkfiXeXY`e\k =\\DfkfiXefekifcj =\\DfkfiXefekifcjGXikjC`jk CXY\cGcXZ\d\ek NXiiXekpI\`jkiXk`fe NFFJKFB@EKIE8K@FE8C@E. G.F.9FO*0 9CC@E?8D#N80/.$*0 N8II8EKP =\FjVainBVXcZhVcYIddah

Related manuals

Manual 57 pages 45.7 Kb