Sears 113.197611, 113.197511, 113.197411 owner manual Short

Page 18

Assembly

3. Identify right side panel by locating let-

ter "R" stamped near center of rear edge.

4. Put right foot assembly inside front edge of right side panel, so foot lever

comes through "J" slot. Use two screws to

attach foot assembly to panel (insert screws through ,fide panel).

5.In similar way, attach left foot assembly to left side panel.

Foot Assembly

\

Side

Panel

I

Assemble and Install Slide Brackets (Only Drawer Model; Door Model: Go

to "Attach Door Hinges")

1. Set out:

-twelve outer brackets -t_velve center slides -three rear supports -grease packet

-tv, enty _a" diam x _/2"long truss head screws

-twenty t/4" lock washers

-_enty v4" diam hex nuts.

2.Grease top and bottom of"center slides.

3.Make twelve slide brackets: insert a center slide all the way into each of 12 outer brackets, then slightly pull back on center slide to make sure stop tabs are engaged.

4. Attach three slide brackets to left side of one rear support, in holes indicated: use one screw per slide bracket (insert screws" through lalger hole in slide bracket); on end of each screw put washer, then nut, and wrench tighten.

%

Center	Slide		Outer	Bracket
/			/
Stop Tab	Stop Tab		Stop Tab	Rear Stop
	_	r_-......_ Short
			Tabs
			Rear Support
		"---'-	Solid	Surface

LargerSlide

HoleBracket

18

Image 18

Contents 113.197511 113.197611Part No. SP5539 Contents Safety Safety Symbol and Signal WordsMajor Hazards KWARNING Wrong Way Feed HazardSafety Instructions Personal Safety InstructionsWork Area Safety Instructions Saw Safety Instructions Workpiece Safety InstructionsBlade Safety Instructions On-Product Safety Labels KWARNINGSafety Assembly Identify PartsQJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Assembly Steps Build Cabinet BaseBuild Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Assembly Attach Door HingesAttach/Install Spacers Attach Side Panels to Bottom ShelfAttach Skirts Center Support Upper Lower Complete Center Slide Assembly Attach DoorsOnly Drawer Model Center Support Assemble Drawers Attach HandwheelMount Motor Shaft has left-hand threa&. Turn nut clock- wise to loosenAssembly Mount Basic Saw AssemblyAdjust Leveling Feet Attach Trim CapsInstall Front Table Attach Slide Arm SupportsClips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism Alignment and Adjustment Install Drawers Only Drawer ModelTo Remove Drawers Only Drawer Model Controls 45, -45 , 90Rip l.ock Controls Alignment and Adjustment Alignment and Adjustment StepsAdjust Column Support Level Front Table Square Crosscut Travel Install Blade Square Blade to Table for Crosscut- tingAlignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Install Guard Align Spreader to BladeComplete Adjustments Go to Digital Display Section and followButton Functions Error MessagesDigital Display =73Install Battery To Replace BatteryAlign Encoders Miter EncoderSet Zero Reference Points For Bevel, Miter, and Elevation Bevel EncoderSet Zero Reference Point For Rip Set Zero Reference Point For Out-RipConversion Table Motor Specifications Power SupplyMotor Protection & Reset Button Electrical ConnectionsTo Change Motor Voltage to 240 A.C To avoid electric shock, unplug sawBefore changing Motor voltage During crosscutting, blade teeth can Crosscutting SafetyCrosscutting Having fingers, hand or arm cut offCrosscuttin Crosscut KerfsMaking Crosscuts StepRepetitive Crosscutting In-Rip and Out-Rip Positions RippingRipping Defined Infeed and Outfeed DirectionsRipping Safety Workpiece PositioningKickback Pinching or binding can happen whenRipping Wrong Way FeedGuard Nose Function Pawls and Spreader FunctionRipping Set-up Procedure If workpiece is pushed along fenceWith kerfs, workpiece could get Making Rip Cuts InleedRipping Hints Dado Blades, Molding HeadsPush Sticks Cutting AidesFences Auxiliary Fence and Push Block for RippingCutting Aides Cutting Aides Straight Edge for Irregular WorkpieceAccessories Safety Information for DadoInformation for Edging Lower Blade Guard Edging without an auxiliary fenceAccessories Lower blade guard can get caught orJam in fence or table kerfs General Information MaintenanceCleaning LubricationAdjustments for Wear Remove screw and nut from swivel lock knobCarriage Bearings Arm and ColumnBlade Changing Replacing PawlsMotor Problem Possible CausesWhat to Do Troubleshooting Saw Problem TroubleshootingCutting Problem Possible CausesTroubleshooting Electronics ProblemBlank Repair Parts Model NOS .197411 and 113.197511Repair Parts Always order by Part Number Not by Key NumberModel NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197611Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 and 113,197511 PartRepair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Repairs Parts Model NOS .197411, 113.197511Repairs Parts Cabinet Assembly for Model 113.197411 For ModelMotor Assembly Guard Assembly Index Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A 113.197411Pail No. SP5539