Sears 113.197611 Mount Motor, Shaft has left-hand threa&. Turn nut clock- wise to loosen

Page 27

Mount Motor

1.Loosen guard clamp screw and lift guard off blade.

2.Use both blade wrenches in scissor ac- tion to loosen blade nut. Note:Arbor

shaft has left-hand threa&. Turn nut clock- wise to loosen.

3.Remove and set aside nut, blade col- lars and blade. They, wifl be re-installed later during alignment and adjustment.

4.I_,ock rip lock. Turn handwheel clock- wise to raise radial arm about 3".

5.Remove styrofoam packing blocks, and clean small pieces of styrofoam off saw. I.ifl motor out of styrofoam base and set on center channel of saw. Remove three table sections and fence.

6.Remove lock nut and flat washer from motor support.

7.Slide bevel cncoder to top position so it will fit into notch in plate index on motor.

8.Slide motor onto motor support. Make sure motor is firmly in place.

9.Re-install flat washer and lock nut.

Tighten lock nut and at same time move bevel lock (located near saw handle) back and forth. Do not over tighten nut.

Lock

Assembly

Motor

Guard

Clamp

Screw

[_-____

Rip

Lock

_

Motor

Lock Nut

SupportWasher

27

Image 27
Contents 113.197511 113.197611Part No. SP5539 Contents Safety Safety Symbol and Signal WordsMajor Hazards Wrong Way Feed Hazard KWARNINGSafety Instructions Personal Safety InstructionsWork Area Safety Instructions Workpiece Safety Instructions Saw Safety InstructionsBlade Safety Instructions KWARNING On-Product Safety LabelsSafety Identify Parts AssemblyQJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Build Cabinet Base Assembly StepsBuild Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Attach Door Hinges AssemblyAttach Side Panels to Bottom Shelf Attach/Install SpacersAttach Skirts Center Support Upper Lower Complete Center Slide Assembly Attach DoorsOnly Drawer Model Center Support Attach Handwheel Assemble DrawersShaft has left-hand threa&. Turn nut clock- wise to loosen Mount MotorMount Basic Saw Assembly AssemblyAttach Trim Caps Adjust Leveling FeetAttach Slide Arm Supports Install Front TableClips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism Alignment and Adjustment Install Drawers Only Drawer ModelTo Remove Drawers Only Drawer Model 45, -45 , 90 ControlsRip l.ock Controls Alignment and Adjustment Alignment and Adjustment StepsAdjust Column Support Level Front Table Square Crosscut Travel Square Blade to Table for Crosscut- ting Install BladeAlignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Align Spreader to Blade Install GuardGo to Digital Display Section and follow Complete Adjustments=73 Error MessagesDigital Display Button FunctionsTo Replace Battery Install BatteryMiter Encoder Align EncodersBevel Encoder Set Zero Reference Points For Bevel, Miter, and ElevationSet Zero Reference Point For Out-Rip Set Zero Reference Point For RipConversion Table Power Supply Motor SpecificationsElectrical Connections Motor Protection & Reset ButtonTo Change Motor Voltage to 240 A.C To avoid electric shock, unplug sawBefore changing Motor voltage Having fingers, hand or arm cut off Crosscutting SafetyCrosscutting During crosscutting, blade teeth canCrosscut Kerfs CrosscuttinStep Making CrosscutsRepetitive Crosscutting Infeed and Outfeed Directions RippingRipping Defined In-Rip and Out-Rip PositionsWorkpiece Positioning Ripping SafetyPinching or binding can happen when KickbackWrong Way Feed RippingPawls and Spreader Function Guard Nose FunctionRipping Set-up Procedure If workpiece is pushed along fenceWith kerfs, workpiece could get Inleed Making Rip CutsDado Blades, Molding Heads Ripping HintsAuxiliary Fence and Push Block for Ripping Cutting AidesFences Push SticksCutting Aides Straight Edge for Irregular Workpiece Cutting AidesAccessories Safety Information for DadoInformation for Edging Edging without an auxiliary fence Lower Blade GuardAccessories Lower blade guard can get caught orJam in fence or table kerfs Lubrication MaintenanceCleaning General InformationRemove screw and nut from swivel lock knob Adjustments for WearArm and Column Carriage BearingsReplacing Pawls Blade ChangingMotor Problem Possible CausesWhat to Do Troubleshooting Possible Causes TroubleshootingCutting Problem Saw ProblemElectronics Problem TroubleshootingBlank Model NOS .197411 and 113.197511 Repair PartsAlways order by Part Number Not by Key Number Repair PartsModel NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 Parts List for Craftsman 10 Electronic Radial SAWModel NOS .197411 and 113.197511 Part Model NOS .197411 and 113.197611 and 113,197511Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Model NOS .197411, 113.197511 Repairs PartsRepairs Parts Cabinet Assembly for Model 113.197411 Model ForMotor Assembly Guard Assembly Index Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A 113.197411Pail No. SP5539