Sears 113.197511, 113.197611, 113.197411 owner manual Assembly, Identify Parts

Page 10

Assembly

Identify Parts

The following parts are included:

Note: Before beginning assembly; check

that atl parts are included. If you are miss-

ing any part, do not assemble saw. Contact your Sears Service Center to get the missing

part. Sometimes small parts can get lost in

packaging material. Do not throw away' any

packajng until saw is put together. Check

packagirN for missing parts before contact- bzg Sea_'. A complete parts list (Repair

Parts) is"at the end of the manual. Use the

list to identi_ the number of the missing part.

A. Basic

Saw Assembly

1

B. Rear

Table

1

C. Spacer

Table

.......................

1

D. Fence

(wooden)

1

E. Front

Table

.........................

1

F. Trim

Cap

2

G. Cabinet Box

1

H. Loose

Parts

Bags

*

Only models with casters include:

I. Caster/Foot

Bag or Box

1

Only model with drawers includes;

J. Drawer Box

1

*Number varies; bags can contain other smaller bags. Note: To make assembly easier, keep contents of each bag together, and separate from contents of other bags.

G

10

Image 10
Contents 113.197611 113.197511Part No. SP5539 Contents Safety Symbol and Signal Words SafetyMajor Hazards KWARNING Wrong Way Feed HazardPersonal Safety Instructions Safety InstructionsWork Area Safety Instructions Saw Safety Instructions Workpiece Safety InstructionsBlade Safety Instructions On-Product Safety Labels KWARNINGSafety Assembly Identify PartsQJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Assembly Steps Build Cabinet BaseBuild Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Assembly Attach Door HingesAttach/Install Spacers Attach Side Panels to Bottom ShelfAttach Skirts Center Support Upper Lower Attach Doors Complete Center Slide AssemblyOnly Drawer Model Center Support Assemble Drawers Attach HandwheelMount Motor Shaft has left-hand threa&. Turn nut clock- wise to loosenAssembly Mount Basic Saw AssemblyAdjust Leveling Feet Attach Trim CapsInstall Front Table Attach Slide Arm SupportsClips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism Install Drawers Only Drawer Model Alignment and AdjustmentTo Remove Drawers Only Drawer Model Controls 45, -45 , 90Rip l.ock Controls Alignment and Adjustment Steps Alignment and AdjustmentAdjust Column Support Level Front Table Square Crosscut Travel Install Blade Square Blade to Table for Crosscut- tingAlignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Install Guard Align Spreader to BladeComplete Adjustments Go to Digital Display Section and followButton Functions Error MessagesDigital Display =73Install Battery To Replace BatteryAlign Encoders Miter EncoderSet Zero Reference Points For Bevel, Miter, and Elevation Bevel EncoderSet Zero Reference Point For Rip Set Zero Reference Point For Out-RipConversion Table Motor Specifications Power SupplyMotor Protection & Reset Button Electrical ConnectionsTo avoid electric shock, unplug saw To Change Motor Voltage to 240 A.CBefore changing Motor voltage During crosscutting, blade teeth can Crosscutting SafetyCrosscutting Having fingers, hand or arm cut offCrosscuttin Crosscut KerfsMaking Crosscuts StepRepetitive Crosscutting In-Rip and Out-Rip Positions RippingRipping Defined Infeed and Outfeed DirectionsRipping Safety Workpiece PositioningKickback Pinching or binding can happen whenRipping Wrong Way FeedGuard Nose Function Pawls and Spreader FunctionIf workpiece is pushed along fence Ripping Set-up ProcedureWith kerfs, workpiece could get Making Rip Cuts InleedRipping Hints Dado Blades, Molding HeadsPush Sticks Cutting AidesFences Auxiliary Fence and Push Block for RippingCutting Aides Cutting Aides Straight Edge for Irregular WorkpieceInformation for Dado Accessories SafetyInformation for Edging Lower Blade Guard Edging without an auxiliary fenceLower blade guard can get caught or AccessoriesJam in fence or table kerfs General Information MaintenanceCleaning LubricationAdjustments for Wear Remove screw and nut from swivel lock knobCarriage Bearings Arm and ColumnBlade Changing Replacing PawlsPossible Causes Motor ProblemWhat to Do Troubleshooting Saw Problem TroubleshootingCutting Problem Possible CausesTroubleshooting Electronics ProblemBlank Repair Parts Model NOS .197411 and 113.197511Repair Parts Always order by Part Number Not by Key NumberModel NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197611Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 and 113,197511 PartRepair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Repairs Parts Model NOS .197411, 113.197511Repairs Parts Cabinet Assembly for Model 113.197411 For ModelMotor Assembly Guard Assembly Index 113.197411 Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.APail No. SP5539