Sears 113.197611, 113.197511, 113.197411 owner manual Controls

Page 36

Controls

CxmU_

Guard

Guard Clamp

Screw

Pawls/Spreader

Wing Nut

Spreader Nut Pawls/Spreader

FunctionOperation/Comments

Guard

Guard Clamp Screw

Pawls/Spreader Wing Nut

Spreader Nut

Pawls/Spreader

Partially protects against blade contact; keeps workpiece from fluttering

during ripping; acts as saw- dust deflector

Frees guard to rotate about blade

Frees pawls/spreader to move up and down

Frees pawls/spreader to move side to side

Reduce kickback by keeping kerf open (spreader func- tion); slow or stop kickback by digging into workpiece (pawls function)

Lock in level position for crosscut; for ripping, rotate until guard nose just clears top surface of workpiece, then lock in place

See Ripping Set- Up for details and illustrations

Turn counterclockwise to loosen, clockwise to tighten

Turn counterclockwise to loosen, clockwise to tighten

Loosen to make adjustment, then tighten.

For safety reasons spreader must be in line with blade. See

Alignment: Spreader to Blade

Set as unit, so pawl is level on workpiece and spreader rides in kerr. For safety reasons set

pawls/spreader before ripping,.

See Ripping Set- Up for details and illustrations

36

Image 36

Contents 113.197511 113.197611Part No. SP5539 Contents Safety Safety Symbol and Signal WordsMajor Hazards KWARNING Wrong Way Feed HazardSafety Instructions Personal Safety InstructionsWork Area Safety Instructions Saw Safety Instructions Workpiece Safety InstructionsBlade Safety Instructions On-Product Safety Labels KWARNINGSafety Assembly Identify PartsQJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Assembly Steps Build Cabinet BaseBuild Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Assembly Attach Door HingesAttach/Install Spacers Attach Side Panels to Bottom ShelfAttach Skirts Center Support Upper Lower Complete Center Slide Assembly Attach DoorsOnly Drawer Model Center Support Assemble Drawers Attach HandwheelMount Motor Shaft has left-hand threa&. Turn nut clock- wise to loosenAssembly Mount Basic Saw AssemblyAdjust Leveling Feet Attach Trim CapsInstall Front Table Attach Slide Arm SupportsClips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism Alignment and Adjustment Install Drawers Only Drawer ModelTo Remove Drawers Only Drawer Model Controls 45, -45 , 90Rip l.ock Controls Alignment and Adjustment Alignment and Adjustment StepsAdjust Column Support Level Front Table Square Crosscut Travel Install Blade Square Blade to Table for Crosscut- tingAlignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Install Guard Align Spreader to BladeComplete Adjustments Go to Digital Display Section and followError Messages Digital DisplayButton Functions =73Install Battery To Replace BatteryAlign Encoders Miter EncoderSet Zero Reference Points For Bevel, Miter, and Elevation Bevel EncoderSet Zero Reference Point For Rip Set Zero Reference Point For Out-RipConversion Table Motor Specifications Power SupplyMotor Protection & Reset Button Electrical ConnectionsTo Change Motor Voltage to 240 A.C To avoid electric shock, unplug sawBefore changing Motor voltage Crosscutting Safety CrosscuttingDuring crosscutting, blade teeth can Having fingers, hand or arm cut offCrosscuttin Crosscut KerfsMaking Crosscuts StepRepetitive Crosscutting Ripping Ripping DefinedIn-Rip and Out-Rip Positions Infeed and Outfeed DirectionsRipping Safety Workpiece PositioningKickback Pinching or binding can happen whenRipping Wrong Way FeedGuard Nose Function Pawls and Spreader FunctionRipping Set-up Procedure If workpiece is pushed along fenceWith kerfs, workpiece could get Making Rip Cuts InleedRipping Hints Dado Blades, Molding HeadsCutting Aides FencesPush Sticks Auxiliary Fence and Push Block for RippingCutting Aides Cutting Aides Straight Edge for Irregular WorkpieceAccessories Safety Information for DadoInformation for Edging Lower Blade Guard Edging without an auxiliary fenceAccessories Lower blade guard can get caught orJam in fence or table kerfs Maintenance CleaningGeneral Information LubricationAdjustments for Wear Remove screw and nut from swivel lock knobCarriage Bearings Arm and ColumnBlade Changing Replacing PawlsMotor Problem Possible CausesWhat to Do Troubleshooting Troubleshooting Cutting ProblemSaw Problem Possible CausesTroubleshooting Electronics ProblemBlank Repair Parts Model NOS .197411 and 113.197511Repair Parts Always order by Part Number Not by Key NumberModel NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197611Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 and 113,197511 PartRepair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Repairs Parts Model NOS .197411, 113.197511Repairs Parts Cabinet Assembly for Model 113.197411 For ModelMotor Assembly Guard Assembly Index Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A 113.197411Pail No. SP5539