Sears 113.197511, 113.197611, 113.197411 owner manual Install Battery, To Replace Battery

Page 49

Digital Display

Install Battery

1. Set out -battery

-battery. cover.

2.Position battery with angled corner on top right and slide battery all the way into opening behind digital display, pushing slightly downward until it snaps into place.

3.Look at display. It should look like this: If it shows nothing, push in and slightly

upwards on battery to remove it, then re- install.

If there still is no display, remove bat- tery, wipe off contacts, then re-install.

If there is still no display, try a new 6V alkaline battery or contact Sears.

4.When display shows correctly, snap bat- tery cover into place.

5.Follow steps to align encoders and set zero reference points.

To Replace Battery

I. lJse screwdriver to pry off battery cover.

2.Push in and slightly upwards on battery to remove it. Install new 6V alkaline bat- terv.

3.Follow steps to set zero reference

poi nts.

49

Image 49

Contents 113.197611 113.197511Part No. SP5539 Contents Safety Symbol and Signal Words SafetyMajor Hazards Wrong Way Feed Hazard KWARNINGPersonal Safety Instructions Safety InstructionsWork Area Safety Instructions Workpiece Safety Instructions Saw Safety InstructionsBlade Safety Instructions KWARNING On-Product Safety LabelsSafety Identify Parts AssemblyQJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Build Cabinet Base Assembly StepsBuild Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Attach Door Hinges AssemblyAttach Side Panels to Bottom Shelf Attach/Install SpacersAttach Skirts Center Support Upper Lower Attach Doors Complete Center Slide AssemblyOnly Drawer Model Center Support Attach Handwheel Assemble DrawersShaft has left-hand threa&. Turn nut clock- wise to loosen Mount MotorMount Basic Saw Assembly AssemblyAttach Trim Caps Adjust Leveling FeetAttach Slide Arm Supports Install Front TableClips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism Install Drawers Only Drawer Model Alignment and AdjustmentTo Remove Drawers Only Drawer Model 45, -45 , 90 ControlsRip l.ock Controls Alignment and Adjustment Steps Alignment and AdjustmentAdjust Column Support Level Front Table Square Crosscut Travel Square Blade to Table for Crosscut- ting Install BladeAlignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Align Spreader to Blade Install GuardGo to Digital Display Section and follow Complete AdjustmentsDigital Display Error MessagesButton Functions =73To Replace Battery Install BatteryMiter Encoder Align EncodersBevel Encoder Set Zero Reference Points For Bevel, Miter, and ElevationSet Zero Reference Point For Out-Rip Set Zero Reference Point For RipConversion Table Power Supply Motor SpecificationsElectrical Connections Motor Protection & Reset ButtonTo avoid electric shock, unplug saw To Change Motor Voltage to 240 A.CBefore changing Motor voltage Crosscutting Crosscutting SafetyDuring crosscutting, blade teeth can Having fingers, hand or arm cut offCrosscut Kerfs CrosscuttinStep Making CrosscutsRepetitive Crosscutting Ripping Defined RippingIn-Rip and Out-Rip Positions Infeed and Outfeed DirectionsWorkpiece Positioning Ripping SafetyPinching or binding can happen when KickbackWrong Way Feed RippingPawls and Spreader Function Guard Nose FunctionIf workpiece is pushed along fence Ripping Set-up ProcedureWith kerfs, workpiece could get Inleed Making Rip CutsDado Blades, Molding Heads Ripping HintsFences Cutting AidesPush Sticks Auxiliary Fence and Push Block for RippingCutting Aides Straight Edge for Irregular Workpiece Cutting AidesInformation for Dado Accessories SafetyInformation for Edging Edging without an auxiliary fence Lower Blade GuardLower blade guard can get caught or AccessoriesJam in fence or table kerfs Cleaning MaintenanceGeneral Information LubricationRemove screw and nut from swivel lock knob Adjustments for WearArm and Column Carriage BearingsReplacing Pawls Blade ChangingPossible Causes Motor ProblemWhat to Do Troubleshooting Cutting Problem TroubleshootingSaw Problem Possible CausesElectronics Problem TroubleshootingBlank Model NOS .197411 and 113.197511 Repair PartsAlways order by Part Number Not by Key Number Repair PartsModel NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 Parts List for Craftsman 10 Electronic Radial SAWModel NOS .197411 and 113.197511 Part Model NOS .197411 and 113.197611 and 113,197511Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Model NOS .197411, 113.197511 Repairs PartsRepairs Parts Cabinet Assembly for Model 113.197411 Model ForMotor Assembly Guard Assembly Index 113.197411 Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.APail No. SP5539