Sears 113.197411, 113.197611, 113.197511 Parts List for Craftsman 10 Electronic Radial SAW

Page 89

Repair Parts

PARTS LIST FOR CRAFTSMAN 10" ELECTRONIC RADIAL SAW

MODEL NOS. 113.197411 AND 113.197611 AND 113.197511

Always order by Part Number - Not by Key Number

FIGURE 3 - YOKE AND MOTOR ASSEMBLY

Key	Part		Description	Key	Part	Description
No	No.			No	No,
1		Yoke Assembly (see Figure 4)		15	STD551012	* Washer, 17/64 x 9/16 x 1/16
2	818922	Screw,	Flat Hd	16	818888	• Motor (Complete) (See Fig+5)
		Plastite No. 8 x 1		17	STD510802	* Screw, Pan Hd
3	818202	Handle, Yoke				Type "T" 8-32 x 5/16
4	815678	Washer, Shaft		18	815802	Guide, Bevel Reader
5	815679-1	Pin, Index		19	818197	Plate, Index
6	STD551043	*Washer,	.505 x 7/8 x 1/16	20	815751	Encoder, Bevel
7	815791	Spring, Bevel		21	STD601105	* Screw, Hex Washer Hd
8	818154	Lever, Bevel Lock		22	STD551010	Type "T" 10-32 x 1/2
9	815813	Nut, Square 1/2-13		22	STD551010	* Washer, 3/16 x 3/8 x 1/32
10	815836	Wedge,	Bevel Spring	23	508153	Shaft, Support w/Plate
!1	818204	Cover, Yoke		24	30495	Nut, Shaft
12	815799	Plug, Yoke		25	62498	Collar, Blade
13	806828	Screw,	Pan Hd	26	9-32668	1-Blade, Saw
		Type	"T" 1/4-20 x 1/2	27	805839-1	Nut, Lock 1/2-13

14815992-1 Screw, Soc. Hd Type "TT" 1/4-20 x 5/8

*Standard Hardware kern may be Purchased Locally.

1Stock Item may be secured Through the Hardware Department of Most Sears Retail or Catalog Order Houses.

•Any attempt to repair this motor may result in unit misalignment and create a HAZARD unless repair is

done by a qualified service technician. Do not loosen the three screws holding the motor support to the motor. This assembly is factory aligned. Repair service is available at your nearest Sears Store.

89

Image 89

Contents Part No. SP5539 113.197511113.197611 Contents Major Hazards SafetySafety Symbol and Signal Words Wrong Way Feed Hazard KWARNINGWork Area Safety Instructions Safety InstructionsPersonal Safety Instructions Workpiece Safety Instructions Saw Safety InstructionsBlade Safety Instructions KWARNING On-Product Safety LabelsSafety Identify Parts AssemblyQJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Build Cabinet Base Assembly StepsBuild Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Attach Door Hinges AssemblyAttach Side Panels to Bottom Shelf Attach/Install SpacersAttach Skirts Center Support Upper Lower Only Drawer Model Complete Center Slide AssemblyAttach Doors Center Support Attach Handwheel Assemble DrawersShaft has left-hand threa&. Turn nut clock- wise to loosen Mount MotorMount Basic Saw Assembly AssemblyAttach Trim Caps Adjust Leveling FeetAttach Slide Arm Supports Install Front TableClips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism To Remove Drawers Only Drawer Model Alignment and AdjustmentInstall Drawers Only Drawer Model 45, -45 , 90 ControlsRip l.ock Controls Adjust Column Support Alignment and AdjustmentAlignment and Adjustment Steps Level Front Table Square Crosscut Travel Square Blade to Table for Crosscut- ting Install BladeAlignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Align Spreader to Blade Install GuardGo to Digital Display Section and follow Complete AdjustmentsDigital Display Error MessagesButton Functions =73To Replace Battery Install BatteryMiter Encoder Align EncodersBevel Encoder Set Zero Reference Points For Bevel, Miter, and ElevationSet Zero Reference Point For Out-Rip Set Zero Reference Point For RipConversion Table Power Supply Motor SpecificationsElectrical Connections Motor Protection & Reset ButtonBefore changing Motor voltage To Change Motor Voltage to 240 A.CTo avoid electric shock, unplug saw Crosscutting Crosscutting SafetyDuring crosscutting, blade teeth can Having fingers, hand or arm cut offCrosscut Kerfs CrosscuttinStep Making CrosscutsRepetitive Crosscutting Ripping Defined RippingIn-Rip and Out-Rip Positions Infeed and Outfeed DirectionsWorkpiece Positioning Ripping SafetyPinching or binding can happen when KickbackWrong Way Feed RippingPawls and Spreader Function Guard Nose FunctionWith kerfs, workpiece could get Ripping Set-up ProcedureIf workpiece is pushed along fence Inleed Making Rip CutsDado Blades, Molding Heads Ripping HintsFences Cutting AidesPush Sticks Auxiliary Fence and Push Block for RippingCutting Aides Straight Edge for Irregular Workpiece Cutting AidesInformation for Edging Accessories SafetyInformation for Dado Edging without an auxiliary fence Lower Blade GuardJam in fence or table kerfs AccessoriesLower blade guard can get caught or Cleaning MaintenanceGeneral Information LubricationRemove screw and nut from swivel lock knob Adjustments for WearArm and Column Carriage BearingsReplacing Pawls Blade ChangingWhat to Do Motor ProblemPossible Causes Troubleshooting Cutting Problem TroubleshootingSaw Problem Possible CausesElectronics Problem TroubleshootingBlank Model NOS .197411 and 113.197511 Repair PartsAlways order by Part Number Not by Key Number Repair PartsModel NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 Parts List for Craftsman 10 Electronic Radial SAWModel NOS .197411 and 113.197511 Part Model NOS .197411 and 113.197611 and 113,197511Repair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Model NOS .197411, 113.197511 Repairs PartsRepairs Parts Cabinet Assembly for Model 113.197411 Model ForMotor Assembly Guard Assembly Index Pail No. SP5539 Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A113.197411