Sears 113.197411, 113.197611, 113.197511 owner manual Troubleshooting

Page 80

Troubleshooting

Cutting Problem

Inaccurate cut

Crosscuts not accurate at indexed miter positions

Possible Cause(s)

Loose locks

Saw blade out of alignment

Sawdust between workpiece and fence

Fence not straight

Swivel lock loose or not locked

Crosscut travel not square with fence

Carriage assembly loose on arm

Arm not indexing properly

Looseness between column tube and column support

What to Do

Check miter, rip, bevel, and swivel locks. See Adjustments for Wear

Check alignment

Keep front table clean

Replace fence

Adjust swivel lock for wear

Square blade crosscut travel

Adjust carriage bearings, then re- align saw

Adjust miter lock for wear

Adjust column support

Depth of crosscut varies from one side of workpiece to other

Saw cuts at slight bevel

Workpiece kerf rough with tooth marks from blade

Blade tends to advance through workpiece too fast during crosscut ring

Table not parallel with radial arm

Blade not square to table

Table not parallel to radial arm Bevel lock loose

Work table not fiat

Carriage bearings loose

Blade not square to fence

Using improper blade for desired finish cut

Blade dull

User pulls blade through workpiece too fast

Level front table

Square blade to table for crosscut- ting and ripping

Level front table

Adjust bevel lock for wear

Replace table

Adjust carriage bearings, then re- align saw

Square blade to fence

Use proper smooth-cutting blade

Sharpen or replace blade

Pull blade slowly and steadily through workpieee

8O

Image 80

Contents Part No. SP5539 113.197511113.197611 Contents Major Hazards SafetySafety Symbol and Signal Words KWARNING Wrong Way Feed HazardWork Area Safety Instructions Safety InstructionsPersonal Safety Instructions Saw Safety Instructions Workpiece Safety InstructionsBlade Safety Instructions On-Product Safety Labels KWARNINGSafety Assembly Identify PartsQJlIF*llfq!lt LHllLltlLllltllllltB Tools Needed For Assembly Assembly Steps Build Cabinet BaseBuild Foot Assemblies Shaped Slot Attach Foot Assemblies Short Assemble Side PanelsOnly Door Model without Casters Assembly Attach Door HingesAttach/Install Spacers Attach Side Panels to Bottom ShelfAttach Skirts Center Support Upper Lower Only Drawer Model Complete Center Slide AssemblyAttach Doors Center Support Assemble Drawers Attach HandwheelMount Motor Shaft has left-hand threa&. Turn nut clock- wise to loosenAssembly Mount Basic Saw AssemblyAdjust Leveling Feet Attach Trim CapsInstall Front Table Attach Slide Arm SupportsClips. Note Table will extend about Beyond Trim caps Assemble Table Lock Mechanism To Remove Drawers Only Drawer Model Alignment and AdjustmentInstall Drawers Only Drawer Model Controls 45, -45 , 90Rip l.ock Controls Adjust Column Support Alignment and AdjustmentAlignment and Adjustment Steps Level Front Table Square Crosscut Travel Install Blade Square Blade to Table for Crosscut- tingAlignment and Adjustment Square Blade to Fence Square Blade to Table for Ripping Adjust Carriage Bearings Make Blade Parallel to Table Install Guard Align Spreader to BladeComplete Adjustments Go to Digital Display Section and followError Messages Digital DisplayButton Functions =73Install Battery To Replace BatteryAlign Encoders Miter EncoderSet Zero Reference Points For Bevel, Miter, and Elevation Bevel EncoderSet Zero Reference Point For Rip Set Zero Reference Point For Out-RipConversion Table Motor Specifications Power SupplyMotor Protection & Reset Button Electrical ConnectionsBefore changing Motor voltage To Change Motor Voltage to 240 A.CTo avoid electric shock, unplug saw Crosscutting Safety CrosscuttingDuring crosscutting, blade teeth can Having fingers, hand or arm cut offCrosscuttin Crosscut KerfsMaking Crosscuts StepRepetitive Crosscutting Ripping Ripping DefinedIn-Rip and Out-Rip Positions Infeed and Outfeed DirectionsRipping Safety Workpiece PositioningKickback Pinching or binding can happen whenRipping Wrong Way FeedGuard Nose Function Pawls and Spreader FunctionWith kerfs, workpiece could get Ripping Set-up ProcedureIf workpiece is pushed along fence Making Rip Cuts InleedRipping Hints Dado Blades, Molding HeadsCutting Aides FencesPush Sticks Auxiliary Fence and Push Block for RippingCutting Aides Cutting Aides Straight Edge for Irregular WorkpieceInformation for Edging Accessories SafetyInformation for Dado Lower Blade Guard Edging without an auxiliary fenceJam in fence or table kerfs AccessoriesLower blade guard can get caught or Maintenance CleaningGeneral Information LubricationAdjustments for Wear Remove screw and nut from swivel lock knobCarriage Bearings Arm and ColumnBlade Changing Replacing PawlsWhat to Do Motor ProblemPossible Causes Troubleshooting Troubleshooting Cutting ProblemSaw Problem Possible CausesTroubleshooting Electronics ProblemBlank Repair Parts Model NOS .197411 and 113.197511Repair Parts Always order by Part Number Not by Key NumberModel NOS .197411 and 113.197611 Base and Column Assembly Model NOS .197411 and 113.197511 Parts List for Craftsman 10 Electronic Radial SAW Model NOS .197411 and 113.197611Model NOS .197411 and 113.197511 Model NOS .197411 and 113.197611 and 113,197511 PartRepair Parts ARM Assembly Table Assembly Foot Assembly Model 113.197511 Model NOS .197411, 113.197511 Repairs Parts Model NOS .197411, 113.197511Repairs Parts Cabinet Assembly for Model 113.197411 For ModelMotor Assembly Guard Assembly Index Pail No. SP5539 Sold by SEARS, Roebuck and CO., Chicago, IL 60684 U.S.A113.197411